Bestway FLOWCLEAR 58678 Manual Del Propietário página 3

SETUP
CHECK LIST
To check the parts inside the manual. Verify that the equipment components represent the model that you had intended to purchase. In case of any
damaged or missing parts at the time of purchase, visit our website bestwaycorp.com/support. Drawings are for illustration purposes only. May not
reflect actual product. Not to scale.
PRODUCT SPECIFICATIONS
Maximum chlorine production per hour:
Sand filter/Filter pump flow range:
Salt concentration:
Water temperature:
Ambient temperature:
Compatible with max water capacity:
RECOMMENDATIONS BEFORE INSTALLATION
• The chlorinator must be installed at the last position of the water circulation pipe (down the direction of the water flow) as shown in "1a. and 1b.".
• Only use sodium chloride (NaCl) salt with a purity of at least 99.8% to fully dissolve it.
• Too low salt content will reduce the efficiency of the chlorinator and result in low chlorine production. High salt content may produce a salty taste
to the pool water and it may cause corrosion to metal fixtures and fittings in the pool.
• The "Pool Salt Table" shows the correct amount of salt required. Refer to the different quantity of water. The salt in the pool will not automatically
decrease.
• Only when the pool water is lost will the salt in the water decrease, and the evaporation of water will not cause the salt to decrease.
Pool capacity
(gal)
1000
1500
2000
3000
4000
5000
6000
7000
If the device shows error E2, it is necessary to reduce the salt concentration: Drain about 20% of the pool water, and then refill with clean water.
Wait 1 hour, and if the error still remains, repeat the operation until the E2 error disappears.
In case the quantity of water of your pool is not listed in the "pool salt table", follow the below formula to calculate the correct quantity of salt to add
to the pool to reach the 3000 ppm of salt concentration, or in case the E1 error appears on the display.
The amount of salt added for the first time:
(lb)
Water capacity(gal)
*0.025
USING THE CHLORINATOR
6 g/h
330-3000 gal/h
3000 ppm (3 g/L）
10-36°C
5-45°C
7000 gal (26495 L)
The amount of salt added for the
first time 3.0 g/L (3000 ppm)
(l) (lb)
3785 25
5677 38
7570 50
11355 75
15140 100
18925 125
22710 150
26495 175
(kg)
Water capacity(l)
*0.003
Code
Icon
number
1
2
3
4
5
6
Pool Salt Table
(kg)
11
17
23
34
45
57
68
79
The amount of salt that needs to be added if the "E1"
(lb)
Water capacity(gal)
*0.0084
Name
Power button Press and hold for 3s to turn on/off the chlorinator
Press and hold for 3s to lock/unlock, and press quickly
Timer button
to adjust working time
When the lock indicator is unlit, the product is unlocked. If
Lock indicator no button is pressed, the product will automatically lock
after 1 minute and the Lock indicator will turn red.
Red: The salt concentration is too high, part of the salt
should be removed from the pool water. Display shows: E2;
Salt
concentration
Green: The salt concentration is at the optimal level;
indicator
Yellow: The salt concentration is too low and salt needs to
be added to the pool water. Display shows: E1.
Water flow
Shows red, no water flow or insufficient water flow
status indicator
Displays running time/remaining time/fault code
Digital Display
Power-on state/standby mode
3
Display code "E1" the amount of
salt that needs to be added
(lb)
8
13
17
25
33
42
50
58
error code displays:
(kg)
Water capacity(l)
*0.001
Illustrate
(kg)
4
6
8
11
15
19
23
26