Publicidad
Idiomas disponibles
Idiomas disponibles
For Walk-behind Snow
Blowers
This snow blower is capable of amputating hands and feet
and throwing objects. Failure to observe the following safety
instructions could result in serious injury.
Training
1. Read, understand and follow all instructions on the
machine and in the manual before operating this unit. Be
thoroughly familiar with the controls and the proper use of
the equipment. Know how to stop the unit and disengage
the controls quickly.
2. Never allow children to operate the equipment.
Never allow adults to operate the equipment without
proper instruction.
3. Keep the area of operation clear of all persons, particularly
small children.
4. Exercise caution to avoid slipping or falling. Especially
when operating the snow blower in reverse.
Preparation
1. Thoroughly inspect the area where the equipment is to be
used and remove all doormats, sleds, boards, wires, and
other foreign objects.
2. Do not operate the equipment without wearing adequate
winter garments. Avoid loose fitting clothing that can get
caught in moving parts. Wear footwear that will improve
footing on slippery surfaces.
3. Never attempt to make any adjustment while the
motor is running, except when specifically
recommended by manufacturer.
4. Always wear safety glasses or eye shields during
operation or while performing an adjustment or repair
to protect eyes from foreign objects that may be thrown
from the machine.
Operation
1. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
2. Exercise extreme caution when operating on or crossing
gravel drives, walks, or roads. Stay alert for hidden
hazards or traffic.
3. After striking a foreign object, stop the motor, remove the
battery pack(s), thoroughly inspect the snow blower for
any damage, and repair the damage before restarting and
operating the snow blower.
4. If the unit start to vibrate abnormally, stop the motor and
check immediately for the cause. Vibration is generally a
warning of trouble.
5. Stop the motor whenever you leave the operating position,
before unclogging the auger/impeller housing or discharge
chute, and when making any repairs, adjustments or
inspection.
6. When cleaning, repairing, or inspecting the snow blower,
stop the motor and make sure the auger/impeller and all
moving parts have stopped.
7. Do not run the motor indoors. Except when starting the
motor and for transporting the snow blower in or out of
the building. Open the outside doors. Exhaust fumes
are dangerous.
8. Exercise extreme caution when operating on slopes.
9. Never operate the snow blower without proper guards and
other safety protective devices in place and working.
10. Never direct the discharge toward people or areas
where property damage can occur. Keep children and
others away.
11. Do not overload the machine at high transport speeds
on slippery surfaces. Look behind and use care when
operating in reverse.
12. Do not overload the machine capacity by attempting to
clear snow at too fast a rate.
13. Disengage the power to the auger/impeller when snow
blower is transported or not in use.
14. Use only attachment and accessories approved by the
manufacturer of the snow blower.
15. Never operate the snow blower without good visibility or
light. Always be sure of your footing, and keep a firm hold
on the handle. Walk; Never run.
16. Never touch a hot motor.
Clearing a Clogged Discharge Chute
m
Rotating blades can cause serious injury.
WARNING!
Never attempt to unclog or clean unit while auger is running.
Hand contact with the rotating auger/impeller inside the
discharge chute is the most common cause of injury
associated with snow blowers. Never use your hand to clean
out the discharge chute.
To clean the chute:
1. SHUT THE MOTOR OFF AND REMOVE THE BATTERY
PACK(S).
2. Wait 10 seconds to be sure the auger blades have
stopped completely.
3. Always use a clean-out tool, such as Snow Joe
chute clean-out tool (Model SJCOT). Visit snowjoe.com
to purchase.
Maintenance and Storage
1. Check shear bolts and other bolts at frequent intervals
for proper tightness to be sure the equipment is in safe
working condition.
2. Always refer to the operator's manual for important details
if the snow blower is to be stored for an extended period.
3. Maintain or replace safety and instruction labels,
as necessary.
2
®
universal
Publicidad
