Publicidad
Idiomas disponibles
Idiomas disponibles
Information
The two screws must be fully tightened (3).
•
Fix the inlay (2) with the two screws (3).
Pos : 51 /RVT/Inbetri ebnahme und Betrieb/Ein- und Ausbau der Inl ays/Ausbau der Inl ays PT- 30 60 @ 0\mod_1418220034721_18.doc x @ 6037 @ @ 1
Removing the inlays from the PT-30 60 press tool
The inlays (1) are held in their position by magnets.
First remove inlay (2) and then inlay (1).
Inlay (2):
Remove the screws (3). Pull out the inlays (2).
Inlay (1):
Slide inlay (1) out by hand against the pull of the magnets.
Pos : 52 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Kapitel übeers chrift+Ü berschrift - T abelle @ 0\mod_1385652188500_18.doc x @ 1618 @ 2 @ 1
8.5 Meaning of the LED display
LED display
Pos : 53 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Alle_LEDs _aus @ 0\mod_1385993057413_18.doc x @ 1630 @ @ 1
All LEDs off.
Pos : 54 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED _l euc htet @ 0\mod_1400057953215_18.doc x @ 2330 @ @ 1
Green LED (2) lights up.
Pos : 55 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED _blinkt @ 0\mod_1400062218616_18.doc x @ 2337 @ @ 1
Green LED (2) flashes.
Pos : 56 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/Grüne_LED s (4) @ 0\mod_1400077557059_18.doc x @ 2379 @ @ 1
Green LEDs (4)
Pos : 57 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/r ote_LED_blinkt @ 0\mod_1400062243654_18.doc x @ 2351 @ @ 1
Red LED (3) flashes.
Pos : 58 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/R ote_LED _leuchtet @ 0\mod_1400062249067_18.doc x @ 2358 @ @ 1
Red LED (3) lights up.
Pos : 59 /RVT/Inbetri ebnahme und Betrieb/Bedeutung der LED- Anz eige/R ote-und_Grüne_LED _blinken_abwec hs elnd @ 0\mod_1400062253497_18.doc x @ 2365 @ @ 1
Red and green LED (2)
flash alternately.
Pos : 60 /RVT/Allgemeines /#### Seitenumbr uch #### @ 0\mod_1380200837280_0.doc x @ 885 @ @ 1
Status/cause
The device is switched off.
On standby.
Insufficient battery charge.
Battery charge display
Device not within the
temperature range.
Device fault.
Service interval reached.
21
PT-12 28; PT-30 60
Measure
Briefly press the start button (1) (see
section 7.5).
Charge or replace battery.
The device only works within a
temperature range from -10 to +50°C. If
the red LED is flashing, the device must be
moved into a warmer or colder area. The
device can be warmed to operating
temperature by means of dry runs.
Press the start button (1). If this is
unsuccessful, the press device is
defective.
Send the device to a specialist workshop.
NOTE!
The pressing operation may not have been
completed; please check and repeat if
required.
Take the press device to be serviced.
EN
Publicidad
