Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Heavy-Duty Air Filter Kit
for TRX Trenchers
Model No. 115-4029
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
1
Removing the Existing Air
Cleaner
No Parts Required
Procedure
1. Stop the machine on a level surface, stop the engine,
remove the ignition key, and lower the boom.
2. Allow the engine to cool completely before
continuing.
If the engine has been running, the muffler
and muffler guard will be hot and could burn
you. This procedure requires you to touch the
muffler guard.
Allow the engine and muffler to cool completely
before installing this kit.
3. Close the fuel shutoff valve.
© 2008—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
No parts required
Intake pipe
Gasket
Breather tube
Engine mounting bracket
Canister assembly
Flange-head bolt
Washer
Lock washer
Nut
Plug
Large air hose
Hose clamp
Weather cap
Register at www.Toro.com.
Qty.
–
Remove the existing air cleaner.
1
1
Install the intake pipe.
1
1
1
3
2
Install the air cleaner.
2
2
1
1
3
Connect the air cleaner to the engine.
1
4. Clean all dirt and debris from the machine.
5. Remove the air cleaner cover (Figure 1).
1. Air cleaner cover
6. Remove and discard the breather tube from the
engine and carburetor (Figure 2).
Form No. 3360-523 Rev A
Installation Instructions
Use
Figure 1
Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Publicidad
Manuales relacionados para Toro 115-4029
Resumen de contenidos para Toro 115-4029
- Página 1 Form No. 3360-523 Rev A Heavy-Duty Air Filter Kit for TRX Trenchers Model No. 115-4029 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Remove the existing air cleaner.
- Página 2 Figure 3 1. Carburetor stud 3. Intake pipe Figure 2 2. Gasket 4. Flange nut 1. Flange nuts 2. Breather tube 2. Install the new breather tube between the intake pipe 7. Remove and save the 2 flange nuts securing the air and the engine (Figure 4).
- Página 3 Installing the Air Cleaner Parts needed for this procedure: Engine mounting bracket Canister assembly Flange-head bolt Washer Lock washer Figure 6 1. Bolt 2. Muffler guard Plug 4. Remove the bolt securing the upper corner of the Procedure valve cover on the left side of the machine (Figure 7). 1.
- Página 4 from the muffler guard, the bolt you removed from the valve cover, and a new flange-head bolt from the kit. Important: Ensure that you insert the mounting bracket between the engine and the muffler guard as shown in Figure 7. Connecting the Air Cleaner to the Engine Parts needed for this procedure:...
- Página 5 Maintenance Replacing the Air Filter Service Interval: Every 250 hours (more frequently if operating conditions are extremely dusty or sandy). Note: Service the air cleaner more frequently if operating conditions are extremely dusty or sandy. Important: To prevent engine damage, always operate the engine with the air filter and cover installed.
- Página 7 Form No. 3360-523 Rev A Kit de filtro de aire de servicio pesado para Zanjadoras TRX Model No. 115-4029 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Retire el limpiador de aire existente.
- Página 8 Instalación del tubo de admisión Parts needed for this procedure: Tubo de admisión Junta Tubo del respiradero Figure 1 Procedure 1. Tapa del limpiador de aire 1. Instale un junta nueva y el tubo de admisión en el 6. Retire y deseche el tubo del respiradero del motor y carburador usando las tuercas con arandela prensada del carburador (Figure 2).
- Página 9 Figure 5 1. Soporte de montaje del 5. Arandela de freno motor Figure 4 2. Soporte de montaje del 6. Tuerca cartucho 3. Perno con arandela 7. Tapón prensada 4. Arandela 2. Instale el tapón en el conector diagnóstico del cartucho del limpiador de aire (Figure 5).
- Página 10 Conexión del limpiador de aire al motor Parts needed for this procedure: Manguera de aire grande Abrazadera Caperuza Procedure 1. Si la entrada de aire no está orientada directamente hacia arriba, afloje el perno y la tuerca que sujetan las abrazaderas de montaje del cartucho, gire el cartucho hasta que la entrada quede hacia arriba, y apriete el perno y la tuerca para sujetar el cartucho (Figure 8).
- Página 11 Figure 9 1. Abrazadera 2. Manguera de aire grande 3. Instale la manguera de aire sobre el tubo de entrada Figure 10 del carburador y el orificio inferior del cartucho 1. Caperuza 3. Entrada de aire (Figure 9). 2. Abrazadera 4.
- Página 12 Maintenance Cambio del filtro de aire Service Interval: Every 250 hours (Con más frecuencia si la zona de trabajo tiene mucho polvo o arena). Note: Revise el limpiador de aire con mayor frecuencia en condiciones de trabajo de mucho polvo o arena. Important: Para evitar dañar el motor, no haga funcionar nunca el motor sin que estén instalados el filtro de aire y la tapa.