Sabo 40-CLASSIC Manual Del Operador página 43

– Pick up the grass collecting bag by the carrying strap and hang in the grass collecting
bag at the top of the mower housing with its two side hooks S1 .
– Attach ejection flap to collecting bag.
Pos: 15.15 / Innen teil/ Vorbe rei tende Arbe iten/1.1 Sc hni tthöhe e ins tellen ( Abbi ldun g I) @ 0\mod _11 152 0122 960 9_6.d ocx @ 3 35 @ 2 @ 1
Adjusting the cutting height (figure I )
Pos: 15.16 / Innen teil/ Sic herhe its hinwei se/Si cherheit shinwei s: Messe r, Moto rStop, Zünd sch lüsse l @ 4 1\mod_1 4470 641 742 73_6. docx @ 4 287 35 @ @ 1
Pos: 15.17 / Innen teil/ Vorbe rei tende Arbe iten/ Schn itt höhe ein stel len Text 4 7er, 4 3er, 5 4er (Pos Nr 1) @ 20\mod_ 134 6321 761 447 _6.docx @ 154 289 @ @ 1
Your desired cutting height is set with the one-hand adjusting lever (1) on the right side
of the mower.
- Bend the lever so far from the housing that the locking cam disengages from the
bore and engages again in the desired position after lateral rotation.
Pos: 15.18 / Innen teil/ Vorbe rei tende Arbe iten/ Schn itt höhe ein stel len Hinwe is mi t VARIO, mit An trie b @ 16\mod _13 317 2267 037 1_6.d ocx @ 1 3428 6 @ @ 1
IMPORTANT
You should only use your mower at the lowest cutting height on even and flat lawn
surfaces!
Please note that the lower cutting height settings are only to be used under
optimum conditions. If your selected cutting height is too low, the sward may be
damaged and even destroyed.
In addition to the cutting height, the driving speed also influences the cutting
pattern and the collection result. Adjust the cutting height and the driving speed
to the grass height to be cut; do not switch on the autodrive, if applicable.
9 BEFORE INITIAL USE
Safety information!
For explanation of symbols, see the table on page 3
Pos: 16.4 /Innente il/Vo r de r Ersten Inbet rieb nahme/ Allgeme ine Siche rhei tsh inweise Ben zinmähe r + Text D LG @ 37\mod _14 3624 817 439 8_6.do cx @ 40 021 4 @ @ 1
Check all screw connections and the spark plug connector for a tight fit. Tighten the
screws, if necessary. You must particularly check the fastening of the cutter bar
(see chapter "Maintenance of the cutter bar").
The blade fastening screw must always be tightened by an authorised workshop. If the
blade screw is tightened excessively or insufficiently, blade coupling and cutter bar may
be damaged or get loose, which can lead to serious injuries.
The lawn mower is fitted with an engine stop device.
Before using the equipment for the first time, make sure that the engine stop safety control
bar is working perfectly. When the control bar is released, engine and cutter bar must
come to a standstill within three seconds.
After release, the bar must always return to the position shown in the "Description of
components" diagram.
If this is not the case, it must be checked immediately by an authorised workshop.
Risk of injury!
If the stopping time of the blade is longer, stop using the device and take it to an
authorised workshop.
Measuring the stopping time
After starting the combustion engine, the blade rotates and a wind noise can be heard.
The stopping time corresponds to the duration of the wind noise after the combustion
engine has been switched off; it can be measured with a stopwatch.
Machine safety and protective devices must not be manipulated or disabled.
Make sure that all protective devices have been attached properly and are not damaged.
Filling with oil (figure Y1 )
Safety information!
For explanation of symbols, see the table on page 3
IMPORTANT
Avoid damage! Engine is delivered without oil. You must add oil before running
the engine.
Pos: 16.23 / Innen teil/ Vor de r E rste n Inbe triebnahme/ Öl einf üllen Text Moto r B& S 5 50 E-Se rie s, 675 EXi, 65 0 Qua ntum @ 44\mod _146 909 069 4063 _6.do cx @ 50 452 4 @ @ 1
Before the first start, fill in engine oil (quantity and quality see technical data) with a funnel
into this opening after unscrewing the dipstick.
– Park the mower on level ground.
– Fill in the oil slowly through the filler. Do not overfill. After filling in the oil, wait for
about one minute and then check the oil level.
Insert the dipstick and tighten it.
40-CLASSIC
– Checking the oil level
Remove the dipstick. Wipe the dipstick with a clean cloth and reinsert it, but do not
tighten. Pull out the dipstick again and read off the oil level. The oil must be at the
top of the full marking (max.). If necessary, refill oil. However, the oil level must not
be above the full marking.
Reinsert the dipstick and tighten it.
Safety information!
For explanation of symbols,
see the table on page 3
45-A CLASSIC, 51-A CLASSIC
– Checking the oil level
Remove the dipstick. Wipe the dipstick with a clean cloth, reinsert and tighten it.
Pull out the dipstick again and read off the oil level. The oil must be at the top of the
full marking (max.). If necessary, refill oil. However, the oil level must not be above
the full marking.
Reinsert the dipstick and tighten it.
All models
- After the first filling, remove the "OIL HAS BEEN DRAINED FOR SHIPPING" sign
at the top of the engine.
Pos: 16.24 / Innen teil/ Vor de r E rste n Inbe triebnahme/1. 1 Kraft stoff einfü llen @ 0\mod_1 115 211 9562 03_ 6.docx @ 371 @ 2 @ 1
Filling with fuel
Safety
For explanation of symbols, see the table on page 3
– Only fill the tank with fresh and clean unleaded standard petrol.
Fuel with up to 10% ethanol is acceptable.
– Unscrew the tank cap.
– Fill tank with fuel using a funnel up to max. lower edge of the filling nozzle.
– Replace tank cap and screw tight.
10 STARTING THE ENGINE
Only start the engine
Always place the mower on a level area which is not covered with high grass (if the grass
is too high it will block the start-up of the cutter bar and make the starting process more
difficult). When the engine is started, the machine must not be tilted on end, if necessary
it must be tilted by pressing the guide bar down so that the cutting tool is pointing in the
direction away from the user, but only as far as absolutely necessary. As long as the
device has not been lowered to the ground again, both of your hands must be on the top
part of the bar.
Pos: 17.5 /Innente il/Starten des Mot ors/ Sta rte rseil griff wäh rend de s Startens fes t umfasse n VORSICHT @ 13\mod_ 128 0234 045 462 _6.docx @ 110 216 @ @ 1
CAUTION
Hold the starter cable handle firmly when starting. The handle may otherwise slip
out of your hand. Risk of injury!
Pos: 17.6 /Innente il/Starten des Mot ors/H inweis: W ICHT IG @ 0\mod_1 115 2133 661 56_ 6.docx @ 385 @ @ 1
IMPORTANT
The engine will only run when the safety control bar on the upper handlebar section
is pressed. The moment the control bar is released, the latter will return into its
original position by spring force, the engine brake is activated and engine and
cutter bar will come to a standstill within three seconds.
Pos: 17.7 /Innente il/Starten des Mot ors/ 1.1 Manue ller Sta rt oh ne Elekt ro-Start (Abb ildu ng D + E) MU STER @ 1 6\mod_1 331 7253 722 94_ 6.docx @ 1343 88 @ 2 @ 1
Pos: 17.8 /Innente il/Starten des Mot ors/ Sta rten de s Moto rs Text SAU10 718, SAU126 75, SAU113 79H+ S, SAU 1217 8 @ 1 4\mod_1 2822 160 931 70_6. docx @ 1 138 78 @ @ 1
– Press the safety control bar (1) onto the upper handlebar section (2) and hold it
there D.
– Slowly pull the starter cable (3) until resistance is felt, then pull it out rapidly E – the
engine starts to run - , slowly recoil the cable.
NOTE
This engine has a temperature-controlled automatic choke.
The engine runs automatically at an optimum maximum speed, which is required for
a clean cut pattern (engine speed = blade speed).
11 SWITCHING OFF THE ENGINE (FIGURE F )
– Release the safety control bar (1) F .
12 EMERGENCY STOPPING
Release the safety control bar and the drive control bar.
– The mower stops.
– The blade comes to a standstill.
– The engine will stop.
ATTENTION
Ensure before every mowing job that the safety control bar engine stop and the
autodrive control bar work properly:
– When the safety control bar is released, engine and cutter bar must come to
a standstill within three seconds.
– When the autodrive control bar is released, the machine must come to an
immediate standstill.
If this is not the case, please consult your nearest authorised workshop.
7
information!
Safety information!
For explanation of symbols, see the table on
page 3
when standing behind the mower.