Kärcher RCV 3 Manual De Instrucciones página 20

Protect carpets using virtual walls, see chapter Setting
up virtual walls.
Switching on the cleaning robot
Note
Place the cleaning robot directly on the charging station
if it cannot be switched on due to a too low charging
state, see chapter Initial start-up.
1. Keep the On/Off button pressed when the cleaning
robot is in standby and not on the charging station.
The indicator light flashes for approx. 15 seconds
while the cleaning robot starts up and then lights up
constantly.
The cleaning robot emits an acoustic signal when
the start-up is complete.
2. Place the cleaning robot directly on the charging
station.
3. Press the On/Off button.
At initial Start-Up, the cleaning robot starts mapping.
In operation, the cleaning robot starts cleaning.
Setting cleaning modes
Cleaning modes can only be set up with the App. Down-
loading the App is described in the chapter Connecting
cleaning robots with WLAN and App.
The following cleaning modes are available:
● Dry cleaning
● Combination cleaning
● Wet cleaning
The suction power and water quantity can be set in each
of the cleaning modes.
Suction power:
● Quiet
● Standard
● Medium
● Turbo
Water quantity:
● Low
● Medium
● High
Switching off the cleaning robot
Note
The cleaning robot cannot be switched off when it is on
the charging station.
Note
Fully charge the cleaning robot before longer work inter-
ruptions.
ATTENTION
Damage due to moisture
Remove the wiper cloth with the wiper cloth holder, see
chapter Removing the wiper cloth holder with wiper
cloth.
Remove the 2-in-1 dust container with water reservoir,
see chapter Removing the 2-in-1 dust container with
water reservoir.
1. Keep the On/Off button pressed when the cleaning
robot is in standby and not on the charging station.
The cleaning robot switches off.
Interrupting cleaning
1. Press any button during cleaning.
The cleaning robot stops.
2. Press the On/Off button.
Cleaning continues.
3. Press the "Return to charging station" button.
Cleaning is cancelled and the cleaning robot returns
to the charging station.
20
Manually sending the cleaning robot for
1. If the cleaning robot is moving, press any button.
The cleaning robot stops.
2. Press the "Return to charging station" button.
The cleaning robot moves to the charging station for
recharging.
The cleaning robot automatically returns to the charging
station for recharging when it has completed a cleaning
task or when it is low on energy during a cleaning pro-
cess.
1. Empty the dust container if necessary, see chapter
Emptying the 2-in-1 dust container with water reser-
voir.
2. Insert the dry wiper cloth into the wiper cloth holder,
see chapter Installing the wiper cloth holder with
wiper cloth.
3. Press the On/Off button.
The cleaning robot starts cleaning.
Note
After emptying the water reservoir, drops may remain in
the hoses. If the cleaning robot is started with an empty
water reservoir, these drops can be discharged.
ATTENTION
Damage to the 2-in-1 dust container due to corro-
sion and chemical content materials
Do not put detergents, disinfectants or other cleaning
products into the 2-in-1 dust container.
Do not pour hot water into the 2-in-1 dust container.
Do not immerse the 2-in-1 dust container in water.
1. Press any button.
The cleaning robot stops.
2. Remove the 2-in-1 dust container with water reser-
voir.
Illustration G
a Open the cover at the top.
b Press the clamp.
c Remove the 2-in-1 dust container with water res-
ervoir.
3. Refill water.
Illustration M
a Pull up the rubber tab.
b Fill with water.
c Press the rubber tab down.
4. Install the 2-in-1 dust container with water reservoir.
Illustration F
a Press the 2-in-1 dust container with water reser-
voir into position until it audibly latches into place.
b Close the cover at the top.
5. Wet the wipe under running water and wring to re-
move excess water
6. Install the wiper cloth, see chapter Installing the wip-
er cloth holder with wiper cloth.
7. Press the On/Off button.
The cleaning robot starts cleaning.
1. Press any button.
The cleaning robot stops.
2. Remove the 2-in-1 dust container with water reser-
voir.
Illustration G
a Open the cover at the top.
b Press the clamp.
English
recharging
Dry wipe
Wet wipe
Refilling water