Kärcher RCV 3 Manual De Instrucciones página 22

d Clean the 2-in-1 dust container with water reser-
voir.
e Fit the filter flap.
f Close the filter flap.
4. Install the 2-in-1 dust container.
Illustration F
a Press the 2-in-1 dust container into position until
it audibly latches into place.
b Close the cover at the top.
5. Press the On/Off button.
Cleaning continues.
Cleaning the dust container
1. Press any button.
The cleaning robot stops.
2. Remove the dust container.
Illustration L
a Open the cover at the top.
b Press the clamp.
c Remove the dust container.
3. Clean the dust container.
Illustration Q
a Fold the flap down.
b Empty the dust container.
c Open the filter flap.
d Remove the filter flap.
e Clean the dust container.
f Fit the filter flap.
g Close the filter flap.
h Fold the flap upwards until it audibly latches into
place.
4. Install the dust container.
Illustration K
a Press the dust container into position until it audi-
bly latches into place.
b Close the cover at the top.
5. Press the On/Off button.
Cleaning continues.
Cleaning the filter
We recommend cleaning the filter regularly. This pre-
vents it from becoming clogged.
1. Press any button.
The cleaning robot stops.
2. Remove the 2-in-1 dust container with water reser-
voir or the dust container, see chapter Removing
the 2-in-1 dust container with water reservoir or Re-
moving the dust container.
3. Remove the filter.
Illustration R
a Open the filter flap.
b Remove the filter flap.
c Empty the 2-in-1 dust container with water reser-
voir or the dust container.
4. Clean the filter under running water with the clean-
ing tool supplied.
5. Allow the filter to dry completely.
6. Install the filter.
Illustration S
a Fit the filter.
b Fit the filter flap.
c Close the filter flap.
7. Install the 2-in-1 dust container with water reservoir
or the dust container, see chapter Installing 2-in-1
dust container with water reservoir or Installing the
dust container.
8. Press the On/Off button.
Cleaning continues.
22
1. Remove the brush.
Illustration T
a Press the clamps together.
b Remove the brush cover.
c Remove the brush.
d Remove the brush bearing.
2. Clean the brush and brush bearing with the cleaning
tool supplied.
3. Install the brush.
Illustration U
a Fit the brush bearing.
b Fit the brush.
c Fit the brush cover and press it down until it audi-
bly latches into place.
Cleaning the side brush
1. Remove the side brush.
Illustration V
2. Clean the side brush.
3. Install the side brush.
Illustration B
Cleaning the fall sensors
Clean the fall sensors monthly.
Illustration W
1. Wipe the fall sensors with a soft cloth.
Replacing components
We recommend replacing the filter after 3 to 6 months.
1. Press any button.
The cleaning robot stops.
2. Remove the 2-in-1 dust container with water reser-
voir or the dust container, see chapter Removing
the 2-in-1 dust container with water reservoir or Re-
moving the dust container.
3. Remove the filter.
Illustration R
a Open the filter flap.
b Remove the filter flap.
c Remove the filter.
4. Install the new filter.
Illustration S
a Fit the filter.
b Fit the filter flap.
c Close the filter flap.
5. Install the 2-in-1 dust container with water reservoir
or the dust container, see chapter Installing 2-in-1
dust container with water reservoir or Installing the
dust container.
6. Press the On/Off button.
Cleaning continues.
We recommend replacing the brush after
6 to12 months.
1. Remove the brush.
Illustration T
a Press the clamps together.
b Remove the brush cover.
c Remove the brush.
d Remove the brush bearing.
2. Install the new brush.
Illustration U
a Fit the brush bearing.
b Fit the brush.
c Fit the brush cover and press it down until it audi-
bly latches into place.
English
Cleaning the brush
Replacing the filter
Replacing the brush