DeWalt DWC860W Manual De Instrucciones página 2

COMPONENTS (Fig. 1)
A. GFCI on cord set
B. On/Off Switch
C. Lock-On button
D. Diamond blade
E. External flange
F. Clamping screw
G. Water tubing
H. Tool inlet
I. Water tubing adapter
J. Water pressure regulator (5 psi)
K. Screw
L. Water nozzle
ASSEMBLY
Switch (Fig. 1, 2)
WARNING: To avoid the possibility of the appliance plug or receptacle getting wet, position
the saw to one side of a wall mounted receptacle to prevent water from dipping onto the
receptacle or plug. The user should arrange a "drip loop" in the cord connecting the saw to
a receptacle (Fig. 2). The "drip loop" is that part of the cord below the level of the receptacle,
or the connector if an extension cord is used, to prevent water traveling along the cord and
coming in contact with the receptacle.
CAUTION: Before plugging in tool, always check to see that the switch actuates properly and
returns to the OFF position when released.
1. Depress and hold the switch (B) to start operation.
2. For continuous operation, press the lock-on button (C) and release the switch. To disengage
the locking button, depress then release the switch.
To Install the Diamond Blade (Fig. 1, 3)
1. Place saw on a stable surface.
2. Place blade (D) on spindle.
3. Using the flange wrench (V) provided, hold the external flange (E)
4. Turn the clamping screw (F) counterclockwise to tighten. Use the T-handle wrench (W)
provided to secure tightly.
5. To remove the blade, reverse this procedure.
Mounting the Wet Cut System (Fig. 1)
WARNING: Do not use wet cut system unless tool is protected by a GFCI.
This system minimizes airborne dust particles while improving cutting quality and blade life.
1. Loosen the depth adjustment knob (M) and pull shoe (N) to it's minimum depth of cut
position.
2. Using a screwdriver, remove the screw (K) located next to the depth adjustment knob
mounted to the casting.
3. Position the water valve assembly such that the hole in the water valve assembly aligns with
the screw hole located in the casting and the forked water valve (L) straddles the blade.
4. Secure in place with screw. DO NOT overtighten the screw; this could damage the water
valve assembly.
Water Valve Assembly (Fig. 1)
WARNING: Never use water valve assembly without a properly functioning pressure
regulator. This could cause damage to the water tubing if excessive pressure builds up.
1. Never use the saw over head. When using water, limit cutting to the horizontal position to
reduce the risk of water entering the tool.
2. Prior to using the tool with the water valve assembly, inspect water tubing (G) for holes
cracks or other damage. Replace with identical replacement parts if a potential weakened or
damaged area is found. Check connections at the tool inlet (H), water valve and adapter (I)
for leaks. If the connection is loose or the tubing is relaxed around barbs, disconnect tubing,
trim tubing back approximately 1" (25.4 mm), then reconnect tubing. Ensure that tubing is
pushed all the way past the barb(s). Check to ensure tight connection.
3. When using the water kit, always use the water pressure regulator (J) provided. Firmly
attach the regulator to the water source, but do not overtighten. Be sure to use the filter
washer (inside regulator intake end) to prevent contaminates from clogging water jet ports.
If regulator is lost or damaged, replace with identical replacement parts.
Use of Extension Cords
• Always plug extension cord into a GFCI receptacle.
• Use only extension cords that are intended for outdoor use. These extension cords are
identified by a marking "Acceptable for use with outdoor appliance; store indoors while
not in use."
• Use only extension cords having an electrical rating not less than the rating of the prod-
uct.
• Do not use damaged extension cords. Examine extension cord before using and replace
if damaged.
• Do not abuse extension cords and do not yank on any cord to disconnect.
Motor
Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than
10% will cause loss of power and overheating. All D
does not operate, check the power supply.
• Keep cord away from heat and sharp edges.
• Always disconnect the extension cord from the receptacle before disconnecting the product
from the extension cord.
OPERATION
WARNING: Use the appropriate blade. Do not use cracked, damaged or excessively worn
blades. Do not use to cut wood or metal.
CAUTION: Wait for the blade to reach the maximum speed and use a slow even feed for
proper cutting.
CAUTION: The DWC860W should only be used on horizontal surfaces (see Water Valve
Assembly).
CAUTION: Use clamps or other practical way to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body is unstable and may lead to
loss of control.
Proper Hand Position (Fig. 8)
WARNING: To reduce the risk of serious personal injury, Always use proper hand position
as shown.
WARNING: To reduce the risk of serious personal injury, always hold securely in anticipation
of a sudden reaction.
Proper hand position requires one hand on the main handle (U) and the other hand on the front
handle (T) as shown.
NOTE: Figure 8 shows the proper hand positon for a left-handed person. For a right-handed
person, reverse the hand positions.
Depth of Cut Adjustment (Fig. 4)
1. Loosen the depth adjustment knob (M) to release.
2. Move the shoe (N) up or down to desired position.
3. Tighten the depth adjustment knob.
WET CUT METHOD (FIG. 1, 4)
WARNING: Do not use wet cut system unless tool is protected by the GFCI.
WARNING: To reduce the risk of electric shock, ensure water will not enter into your tool. Do
not touch plug with wet hands.
1. Follow the instructions described under Mounting the Wet Cut System.
2. To regulate the water flow, open the water valve by pivoting the lever (O) away from the unit.
3. To close water valve, push the lever toward the unit.
3. Proceed as described below for straight or angled cuts.
STRAIGHT CUTS (FIG. 1)
1. Using a marker or grease pencil, mark the area to be cut.
2. Place the shoe of the saw on the workpiece ensuring that the blade does not touch the
workpiece.
3. Align the external part of the cutting guide (P) with the cut outline on the workpiece.
4. Turn the tool on and wait for the blade to reach its maximum velocity.
M. Depth adjustment knob
N. Shoe
O. Water valve lever
P. Cutting guide
Q. Bevel adjustment knob
R. Brush covers
S. Brush assembly
T. Front handle
U. Main handle
V. flange wrench
W. T-handle wrench
WALT tools are factory tested; if this tool
E
FIG. 1
T
S
R
N
Q
P
E
V
A
W
FIG. 2
FIG. 4
O
M
FIG. 6
R
FIG. 8
T
5. Move the tool slowly and evenly forward, following the cut line.
ANGLED CUTS (FIG. 1, 5)
1. Using a marker or grease pencil, mark the area to be cut.
2. Release the bevel adjustment knob (Q) and move it to the desired angle.
3. After selecting the desired angle, tighten the knob to secure the shoe.
4. Align the internal part of the cutting guide (P) with the cut line on the workpiece.
5. Turn the tool on and wait for the blade to reach its maximum velocity.
6. Move the tool slowly and evenly forward, following the cut line.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect
tool from power source before making any adjustments or removing/installing attachments
or accessories.
Cleaning
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Brushes (Fig. 6, 7)
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect
tool from power source before making any adjustments or removing/installing attachments
or accessories.
U
C
M
B
H
M
L
D
F
J
FIG. 3
E
F
FIG. 5
N
FIG. 7
S
U
O
K
G
I