EINHELL TC-MG 250 CE Manual De Instrucciones página 14

The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Mains voltage: .........................220-240 V~ 50 Hz
Power input: .............................................. 250 W
Idling speed: ............................ 11000-20000 rpm
Sanding/grinding area: .............. 90 x 90 x 90 mm
Oscillation angle: ..............................................3°
Protection class: ...........................................II /
Weight: .......................................................1.2 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 84.5 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 91.5 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Handle
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Anl_TC_MG_250_CE_SPK13.indb 14 Anl_TC_MG_250_CE_SPK13.indb 14
= 13.949 m/s
2
h
2
- 14 -
GB
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Fitting the plug-in tools (Figures 1/2)
•
To fit the plug-in tools safely you should hold
the multifunction tool so that the ON/OFF
switch (1) points down and the tool mounting
(2) faces up.
•
Place the plug-in tool (e.g. the triangular
grinding/sanding plate or Saw blade) on the
tool mounting (2) so that the pins of the tool
mounting (2) fit into the recesses in the plug-
in tool.
25.08.2022 13:36:41 25.08.2022 13:36:41