Publicidad
Idiomas disponibles
Idiomas disponibles
- branches under tension should be cut from the bottom
up to avoid binding the chain saw
MAINTENANCE / SERVICE
•
This tool is not intended for professional use
•
Always keep tool clean (especially ventilation slots H )
! remove battery from tool before cleaning
- clean the tool with a damp cloth (do not use cleaning
agents or solvents)
- remove and brush clean the cover plate, chain and
chain bar after 1 to 3 hours of use
- clean the area under cover plate, drive sprocket and
chain bar assembly using a soft brush and clean cloth
- clean oil outlet with a clean cloth
•
Regularly check for obvious defects such as loose,
dislodged or damaged chain and chain bar, loose fixings,
and worn or damaged components
•
Carry out necessary maintenance and repairs before
using the chain saw
•
Proper functioning of the automatic oiler can be checked
by running the chain saw and pointing the tip of the chain
bar towards a piece of cardboard or paper on the ground
! do not touch the ground with the chain (ensure
safety clearance of 20 cm)
- if an increasing oil pattern developes, the automatic
oiler is operating fine
- if there is no oil pattern, despite a full oil reservoir,
see"TROUBLESHOOTING" or contact your dealer
•
Never sharpen the saw chain yourself. Replace the saw
chain or have the saw chain professionally resharpened
at a SKIL service station.
•
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
! before returning, the oil reservoir must be
completely emptied
•
Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
•
Storage
- if the chain saw is to be stored for a longer period of
time, clean chain and chain bar
- when storing tool, the oil reservoir must be completely
emptied
- use chain guard E when storing the tool
- store the tool indoors in a dry and locked-up place, out
of reach of children
TROUBLESHOOTING
•
The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify
and correct the problem, contact your dealer or service
station)
! in case of electrical or mechanical malfunction,
immediately switch off the tool and remove battery
Tool does not operate
- kickback brake is activated -> pull hand guard D2
back in position
- empty battery -> charge battery
- hot battery -> let battery cool down
- internal fault -> contact dealer/service station
Tool operates intermittently
- internal wiring defective -> contact dealer/service
station
- on/off switch defective -> contact dealer/service station
Dry chain
- no oil in reservoir -> refill oil
- vent in oil reservoir cap clogged -> clean cap
- oil passage clogged -> clean oil passage outlet
Brake does not stop chain
- kickback brake/run-down brake defective -> contact
dealer/service station
Chain/chain bar overheats
- no oil in reservoir -> refill oil
- vent in oil reservoir cap clogged -> clean cap
- oil passage clogged -> clean oil passage outlet
- chain is overtensioned -> adjust chain tension
- dull chain -> sharpen chain or replace
Tool vibrates abnormally
- chain tension too loose -> adjust chain tension
- dull chain -> sharpen chain or replace
- chain worn out -> replace chain
- chain teeth are facing in the wrong direction ->
reassemble with chain in correct direction
ENVIRONMENT
Only for EU countries
•
Do not dispose of electric tools, accessories and
packaging together with household waste material
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 8 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
Only for UK
•
Do not dispose of electric tools, accessories and
packaging together with household waste material
- in observance of on Waste Electric and Electronic
Equipment Regulations 2013 (SI 2013/3113), electric
tools that have reached the end of their life must be
collected separately and returned to an environmentally
compatible recycling facility
- symbol 8 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
NOISE / VIBRATION
•
Measured in accordance with EN 62841 the sound
pressure level of this tool is 93 dB(A) (uncertainty
K = 3 dB) and the sound power level 103 dB(A)
(uncertainty K = 2.2 dB), and the vibration 4.28 m/s²
(triax vector sum; uncertainty K = 1.5 m/s²)
•
The vibration emission level has been measured in
20
Publicidad
