Publicidad
Idiomas disponibles
Idiomas disponibles
Weight
Subject to technical changes!
Noise
m WARNING: Noise can have serious effects on your
health. If the machine noise exceeds 85 dB (A), please
wear suitable hearing protection.
On-load factor* = is the percentage of the operating
time, in which the machine can be used continuously
under normal temperature conditions. In relation to a
10-minute time period this means, for example, that
with a duty cycle of 20%, that it can be used for 2 min-
utes and then there should be a break of 8 minutes. If
you exceed the duty cycle values then this will trigger
the overheating protection which will bring the device
to a stop until it has cooled down to the normal working
temperature. Exceeding the duty cycle values continu-
ously can damage the device.
7.
Unpacking
Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available). Check that
the delivery is complete. Check the device and acces-
sory parts for transport damage. In case of complaints
the dealer must be informed immediately. Subsequent
complaints will not be accepted. If possible, store the
packaging until the warranty period has expired. Read
the operating manual to make yourself familiar with
the device prior to using it. Only use original parts for
accessories as well as for wearing and spare parts.
Spare parts are available from your specialized dealer.
Specify our part numbers as well as the type and year
of construction of the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
8. Attachment / Before starting the
equipment
Place of installation
Make sure the work area is adequately ventilated. If
the device is operated without sufficient cooling, the
operating time is reduced and overheating can occur.
30 | GB
6 kg
Additional protective measures may be required for
this:
• The device must be set up freely, with a distance of
at least 0.5 m all around.
• Ventilation slots must not be blocked or covered.
• The device may not be used as a shelf, and no tools
or anything else may be placed on the device.
• It must be operated in a dry and well-ventilated work
environment.
Connecting the cutting torch
• Insert the plasma burner plug (10a) into the plasma
burner connection socket (10) and tighten the union
nut hand-tight (see Fig. 1,3 + 4).
• Insert the plasma burner power plug (11a) into the
plasma burner power socket (11) and tighten the un-
ion nut hand-tight (see Fig. 1,3 + 4).
Connecting the ground cable
• Connect the ground terminal plug (9a) with the
ground terminal - connection socket (9). Make sure
that the connecting shaft is first connected and then
turned. The connecting shaft must face upwards
when plugging in the ground cable plug (9a). After
plugging in, the connecting shaft must be rotated
in a clockwise direction until it reaches the stop, in
order to lock it in place (see Fig. 1,3 + 5). This does
not require force!
Connect the compressed air hose
• Connect the compressed air hose (19) on the back of
the plasma cutter to the compressed air connection
(19a). To do so, insert the side of the compressed air
hose into the compressed air connection (19a) of the
plasma cutter without a quick connector (see Fig. 9).
• The pressure can be set via the knob (21) on the
condensate separator (see Fig. 9 - 12). Select a
pressure of 4–4.5 bar.
• In order to release the compressed air hose (19),
you must press the locking mechanism of the com-
pressed air connection (19a) and pull out the com-
pressed air hose (19) at the same time.
The compressed air source must have a filter and reg-
ulator.
m IMPORTANT!
You must fully assemble the appliance before using it
for the first time!
www.scheppach.com
Publicidad
