Makita PM001G Manual De Instrucciones página 16

5. Do not short the battery cartridge:
( 1 ) Do not touch the terminals with any con-
ductive material.
Avoid storing battery cartridge in a con-
( 2 )
tainer with other metal objects such as
nails, coins, etc.
Do not expose battery cartridge to water
( 3 )
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6 . Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 ° C (122 ° F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge. S u c h c o n d u c t m a y r e s u l t i n a
fire, excessive heat, or explosion.
9 . Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
f o r w a r d i n g a g e n t s , s p e c i a l r e q u i r e m e n t o n p a c k -
aging and labeling must be observed.
For preparation of the item being shipped, consult-
i n g a n e x p e r t f o r h a z a r d o u s m a t e r i a l i s r e q u i r e d .
Please also observe possibly more detailed
n a t i o n a l r e g u l a t i o n s .
Tape or mask o open contacts and pack up the
battery in such a manner that it cannot move
a r o u n d i n t h e p a c k a g i n g .
11. W hen disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specified by Makita. Installing the batteries to
non-compliant products may result in a fire, exces-
s i v e h e a t , e x p l o s i o n , o r l e a k o f e l e c t r o l y t e .
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
1 4 . During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
1 6 . Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may cause heating, catching fire,
burst and malfunction of the tool or battery car-
tridge, resulting in burns or personal injury.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near high-voltage electri-
cal power lines. I t m a y r e s u l t i n a m a l f u n c t i o n o r
breakdown of the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
a l s o v o i d t h e M a k i t a w a r r a n t y f o r t h e M a k i t a t o o l a n d
c h a r g e r .
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 ° C - 40 ° C (50 ° F - 104 ° F). Let
a hot battery cartridge cool down before
charging it.
4 . W hen not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
ASSEMBLY
CAUTION:
Always be sure that all the battery
cartridges are removed before carrying out any
work on the machine. Failure to remove all the bat-
tery cartridges may result in serious personal injury
f r o m a c c i d e n t a l s t a r t - u p .
Assembling blower pipes
1. L o o s e n t h e c l a m p s c r e w .
Fig.2: 1. C l a m p s c r e w
2. I n s t a l l t h e c o n t r o l h a n d l e t o t h e s w i v e l p i p e a n d
t i g h t e n t h e c l a m p s c r e w .
Fig.3: 1. C o n t r o l h a n d l e 2. S w i v e l p i p e 3. C l a m p
s c r e w
NOTICE:
Be careful not to twist the cable of the
control handle when attaching the control handle
to the swivel pipe.
3.
L o o s e n t h e s c r e w o n t h e h o s e c l a m p , a n d t h e n
a t t a c h t h e h o s e c l a m p t o t h e e n d n o z z l e . A l i g n t h e
g r o o v e s o n t h e e n d n o z z l e w i t h t h e p r o t r u s i o n s o n t h e
s w i v e l p i p e , t h e n a t t a c h t h e e n d n o z z l e t o t h e s w i v e l
p i p e , a n d t h e n t i g h t e n t h e s c r e w o n t h e h o s e c l a m p .
Fig.4: 1. End nozzle 2. H o s e c l a m p 3. S w i v e l p i p e
4. G r o o v e 5. P r o t r u s i o n 6. S c r e w
4. L o o s e n t h e s c r e w o n t h e h o s e c l a m p , t h e n a t t a c h
t h e n o z z l e l e v e r t o t h e h o s e c l a m p , a n d t h e n a t t a c h t h e
hose clamp to the flexible pipe. Attach the swivel pipe to
the flexible pipe, and then tighten the screw on the hose
c l a m p .
Fig.5: 1. S w i v e l p i p e 2. N o z z l e l e v e r 3. H o s e c l a m p
4. Flexible pipe 5. S c r e w
16 ENGLISH