Manuales relacionados para Sauder Viabella 420122
Resumen de contenidos para Sauder Viabella 420122
- Página 1 Storage Cabinet NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. English pg 1-22 Français pg 23-25 Español pg 26-28...
- Página 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-22 Hammer Not actual size Français 23-25 Español 26-28 Skip the power trip. Safety 29-30 This time. Warranty...
- Página 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. RIGHT END (1) LEFT END (1) TOP (1)
- Página 4 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. MOLDING HIDDEN CAM - 15 CAM DOWEL - 15 METAL BRACKET - 8 CONNECTOR - 2 STRAIGHT 40H CURVED 31G CORNER BRACKET - 2 144K PULL - 3 HINGE - 2...
- Página 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Push fi fteen HIDDEN CAMS (1F) into the ENDS (A and B), å UPRIGHTS (E and F), BOTTOM BRACE (L), and CENTER BRACE (P).
- Página 6 Step 2 Fasten the UPRIGHTS (E and F) to the TOP (C). Tighten å four HIDDEN CAMS. S u r f a c H I D D E N i t h o S u r f a c H I D D E N i t h Finished edge...
- Página 7 Step 3 Fasten the TOP BRACES (D) to the TOP (C). Use nine å BLACK 1-1/8" PAN HEAD SCREWS (9S). Just think. The sooner you do this, the sooner NOTE: Do not over tighten the SCREWS into the TOP. å you do something else.
- Página 8 Step 4 Fasten the ENDS (A and B) to the TOP (C). Tighten four å HIDDEN CAMS. Maximum Arrow 210 degrees Minimum 190 degrees Finished edge S u r f a c H I D D E N i t h Finished edge S u r f a c...
- Página 9 Step 5 Fasten the BOTTOM (H) to the UPRIGHTS (E and F). Use å four BLACK 1-15/16" FLAT HEAD SCREWS (113S). 113S BLACK 1-15/16" FLAT HEAD SCREW (4 used in this step) Finished edge...
- Página 10 Step 6 Tap two MOLDING CONNECTORS (19F) into the notches å in the BASE MOLDINGS (I, J, and K). Use your hammer to tap the MOLDING CONNECTORS (19F) into the notches in the MOLDINGS. Flat end Flat end Unfi nished surface Unfi...
- Página 11 Step 7 Fasten the FRONT BASE MOLDING (I) to the BOTTOM (H). Use å fi ve BLACK 1-1/8" PAN HEAD SCREWS (9S). NOTE: Do not over tighten the SCREWS (9S) into the BOTTOM. å Fasten the BASE MOLDINGS (J and K) to the BOTTOM (H). Use å...
- Página 12 Step 8 Fasten eight METAL BRACKETS (4G) to the BOTTOM å BRACE (L) and PLINTHS (N, O, and Q). Use eight BLACK Now might be a 9/16" LARGE HEAD SCREWS (1S). good time to refresh your drink. NOTE: Be sure the BRACKETS are even with the edges of å...
- Página 13 Step 9 Fasten the BRACES (L and P) to the BOTTOM (H). Tighten å six HIDDEN CAMS. Maximum Arrow 210 degrees Fasten the BOTTOM BRACE (L) to the CENTER BRACE (P). å Use one BLACK 1-15/16" FLAT HEAD SCREW (113S). Minimum 190 degrees 113S...
- Página 14 Step 10 Fasten the CORNER BRACKETS (31G) to the BASE å MOLDINGS (I, J, and K) exactly as shown. Use four BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (4 used in this step)
- Página 15 Step 11 Fasten the SIDE SKIRTS (M and R) to the BRACKETS (4G and 31G). å Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). Unfi nished edge BLACK 9/16" LARGE HEAD SCREW (8 used in this step) Unfi nished edge...
- Página 16 Step 12 Fasten the CENTER PLINTH (Q) to the FRONT BASE å MOLDING (I) and CENTER BRACE (P). Use two BLACK Maximum Arrow 9/16" LARGE HEAD SCREWS (1S) and tighten one 210 degrees HIDDEN CAM. Minimum 190 degrees BLACK 9/16" LARGE HEAD SCREW (2 used in this step) Curved edge...
- Página 17 Step 13 Fasten the PLINTHS (N and O) to the FRONT BASE å MOLDING (I) and CORNER BRACKETS (31G). Use six BLACK 9/16" LARGE HEAD SCREWS (1S). BLACK 9/16" LARGE HEAD SCREW (6 used in this step) Curved edge...
- Página 18 Step 14 Carefully turn your unit over onto its front edges. Unfold å the BACK (S) and lay it over your unit. If you're doing this to help a friend, don't Make equal margins along all four edges of the BACK (S). å...
- Página 19 Step 15 Fasten the two CURVED HINGES (40H) to one of the DOORS (T). å Use four BLACK 1/2" FLAT HEAD SCREWS (11S). Fasten the four STRAIGHT HINGES (13H) to the remaining two å DOORS (T). Use eight BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2"...
- Página 20 Step 16 Carefully stand your unit upright. å Before fastening the DOOR to your unit, be sure the mounting screw is against the stops as shown in the diagram. If it å isn't, loosen the mounting screw to slide it against the stops. Then tighten the mounting screw. Fasten the DOOR (T) with the CURVED HINGES to the LEFT UPRIGHT (F) as shown in the lower diagram.
- Página 21 Step 17 Refer to the enlarged diagram to identify the parts on å the HINGES. The DOORS may need some adjustments. Follow the text below å to make needed adjustments. DOOR ADJUSTMENTS: å To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out.
- Página 22 Step 18 NOTE: One of the DOORS is purposely not shown in this diagram. å Push the RUBBER SLEEVES (2R) over the METAL PINS (1R). Insert the METAL PINS into the hole locations of your choice å in the ENDS (A and B) and UPRIGHTS (E and F). Set the ADJUSTABLE SHELVES (G) onto the METAL PINS. NOTE: Please read the back pages of the instruction booklet for important safety information.
- Página 23 Meuble de rangement Utilisez les instructions d’ a ssemblage en français avec les NOUS SOMMES LA POUR VOUS AIDER! schémas étape par étape du manuel d’instruction en anglais. Nous faisons de notre mieux pour nous assurer que votre meuble Chaque étape en français correspond à la même étape arrive dans d’excellentes conditions.
- Página 24 ÉTAPE 1 ÉTAPE 7 Ne pas serrer les EXCENTRIQUES ESCAMOTABLES dans Fixer la MOULURE DE SOCLE AVANT (I) au DESSOUS (H). cette étape. Utiliser cinq VIS TÊTE GOUTTE DE SUIF 28 mm NOIRES (9S). Assembler l'élément sur un sol à moquette ou sur le carton vide REMARQUE : Ne pas trop serrer les VIS (9S) dans le DESSOUS.
- Página 25 ÉTAPE 13 ÉTAPE 17 Fixer les PLINTHES (N et O) à la MOULURE DE SOCLE AVANT (I) Consulter le schéma agrandi pour identifi er les pièces et aux CONSOLES À ÉQUERRE (31G). Utiliser six VIS TÊTE des CHARNIÈRES. LARGE 14 mm NOIRES (1S). Il faut peut-être ajuster les PORTES.
- Página 26 Gabinete para almacenaje Use estas instrucciones de ensamblaje en español junto con las ESTAMOS AQUI PARA AYUDAR! fi guras paso-a-paso provistas en el folleto inglés. Cada paso Tratamos de asegurar que su mueble llega en condición en español corresponde al mismo paso en inglés. Se destacan excelente.
- Página 27 PASO 1 PASO 7 No apriete los EXCÉNTRICOS ESCONDIDOS en este paso. Fije la MOLDURA DE BASE DELANTERA (I) al FONDO (H). Utilice cinco TORNILLOS NEGROS DE CABEZA REDONDA de 28 mm (9S). Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso.
- Página 28 PASO 13 PASO 17 Fije los PLINTOS (N y O) a la MOLDURA DE BASE DELANTERA (I) Consulte el diagrama ampliado para identifi car las piezas de y a las MÉNSULAS DE ESQUINA (31G). Utilice seis TORNILLOS las BISAGRAS. NEGROS DE CABEZA GRANDE de 14 mm (1S). Las PUERTAS pueden requerir de ajustes.
- Página 29 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded dresser drawers and •...
- Página 30 ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Cajones y estantes de cómoda •...
- Página 31 5-YEAR LIMITED WARRANTY 1. provides limited warranty coverage to the original purchaser of this product for a 4. This Warranty applies only to warranted defects that fi rst arise and are reported period of fi ve years from the date of purchase against defects in materials or to within the warranty coverage period.