Descargar Imprimir esta página

Publicidad

Enlaces rápidos

sauder.com
Credenza
Dakota Pass Collection | Model 420408
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
Your center of
attention.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-24
Français pg 25-28
Español pg 29-32
Lot # 389552
05/03/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Publicidad

loading

Resumen de contenidos para Sauder Credenza 420408

  • Página 1 Dakota Pass Collection | Model 420408 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
  • Página 2 • Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly! • This Sauder unit is designed for use with televisions weighing less than 135 pounds. Never use with a TV that weighs more.
  • Página 3: Part Identifi Cation

    GLASS DOOR (2) RIGHT UPRIGHT (1) LARGE SHELF MOLDING (2) ADJUSTABLE SHELF (2) LEFT UPRIGHT (1) BOTTOM MOLDING (1) LARGE ADJUSTABLE SHELF (2) TOP (1) DOOR MOLDING (2) RIGHT FRONT LEG (1) BOTTOM (1) LEFT FRONT LEG (1) www.sauder.com/services 420408 Page 3...
  • Página 4 15S SILVER 5/8" MACHINE SCREW - 4 12S BROWN 1" FLAT HEAD SCREW - 4 BLACK 2-1/4" FLAT HEAD SCREW - 6 GOLD 1" MACHINE SCREW - 2 SILVER 1-1/2" MACHINE SCREW - 2 113S BLACK 1-15/16" FLAT HEAD SCREW - 9 Page 4 420408 www.sauder.com/services...
  • Página 5 Assemble your unit on a carpeted fl oor or on the empty carton to å avoid scratching your unit or the fl oor. To begin assembly, push a SAUDER TWIST-LOCK® FASTENER (10F) å into the large holes in the BOTTOM (G).
  • Página 6 The arrow in the HIDDEN CAM must point toward the Arrow hole in the edge of the board. Hole Arrow (12 used) Turn twelve CAM SCREWS (8F) into the FRONT LEGS (M å and N) and TOP MOLDING (P). Page 6 420408 www.sauder.com/services...
  • Página 7 Fasten the LEFT END (B) to the LEFT FRONT LEG (N). å Tighten three HIDDEN CAMS. Edge with TWIST-LOCK® FASTENERS S u r f a c i t h H I D D E N These surfaces should be even. The LEG will overhang this edge www.sauder.com/services 420408 Page 7...
  • Página 8 Step 4 Fasten the TOP MOLDING (P) to the TOP (F). Tighten six å HIDDEN CAMS. Page 8 420408 www.sauder.com/services...
  • Página 9 Fasten the UPRIGHTS (C, D, and E) to the TOP (F). å Tighten six TWIST-LOCK® FASTENERS. ® How to use the SAUDER TWIST-LOCK FASTENER 1. Insert the dowel end of the FASTENER into the hole of the adjoining part. NOTE: The dowel end of the FASTENER must remain fully inserted in the hole of the adjoining part while locking the FASTENER.
  • Página 10 Notched edge Notched edge Slide the SHELF MOLDINGS (Q) onto the notched edge. These edges must be Notched edge even. These edges must be Slide the SHELF even. MOLDINGS (R) onto the notched edge. Page 10 420408 www.sauder.com/services...
  • Página 11 S u r f a c i t h I S T - L O F A S T E N ® E R S 113S BLACK 1-15/16" FLAT HEAD SCREW (6 used in this step) www.sauder.com/services 420408 Page 11...
  • Página 12 Tighten eight TWIST-LOCK® FASTENERS. Fasten the REAR LEGS (O) to the ENDS (A and B). Use six å BLACK 2-1/4" FLAT HEAD SCREWS (26S). BLACK 2-1/4" FLAT HEAD SCREW (6 used in this step) Angled edge Angled edge Page 12 420408 www.sauder.com/services...
  • Página 13 Fasten the BACK (H) to your unit using the NAILS (1N). å NOTE: Be sure to tap NAILS into the holes that line up å over the UPRIGHTS. NAIL (58 used in this step) These holes must line up over the UPRIGHTS. www.sauder.com/services 420408 Page 13...
  • Página 14 å NOTE: Be sure to use the holes shown. å BLACK 9/16" LARGE HEAD SCREW (9 used in this step) 113S BLACK 1-15/16" FLAT HEAD SCREW (3 used in this step) BLACK 9/16" LARGE HEAD SCREW Page 14 420408 www.sauder.com/services...
  • Página 15 LEGS (M and N) and TOP MOLDING (P). Rome. This can be built in a day. Then, tap the MOLDING CONNECTORS (17F) completely into å the notches with a hammer and straight edge screwdriver. www.sauder.com/services 420408 Page 15...
  • Página 16 Step Step 12 Carefully stand your unit upright. å Push a DOOR STOP (4I) into each LEFT and RIGHT UPRIGHT (E å and D) and two DOOR STOPS (4I) into the UPRIGHT (C). Page 16 420408 www.sauder.com/services...
  • Página 17 HINGES to make sure you have the correct one in this step. Fasten four CURVED HINGES (14H) to the DOORS (I). Use å eight BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2” FLAT HEAD SCREW (8 used in this step) More curve Less curve www.sauder.com/services 420408 Page 17...
  • Página 18 Step Step 14 Fasten four HINGES (40H) to the GLASS DOORS (J). Use å eight BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2" FLAT HEAD SCREW (8 used in this step) Page 18 420408 www.sauder.com/services...
  • Página 19 Fasten a KNOB (28K) to the DOOR (I). Use a 1" å MACHINE SCREW (50S). Hinge Repeat this step fastening the other DOOR (I) to the å LEFT END (B). GOLD 1" MACHINE SCREW (2 used in this step) www.sauder.com/services 420408 Page 19...
  • Página 20 Repeat this step fastening the other GLASS DOOR (J) to å the LEFT UPRIGHT (E). BROWN 1" FLAT HEAD SCREW See the next step for DOOR adjustments. (4 used in this step) å SILVER 1-1/2" MACHINE SCREW (2 used in this step) Page 20 420408 www.sauder.com/services...
  • Página 21 Tighten the screws after making adjustments. To adjust the DOORS in or out (depth), loosen the mounting å screw one turn and move the DOORS in or out, as needed. Tighten the mounting screw after making adjustments. (vertical adjustment) www.sauder.com/services 420408 Page 21...
  • Página 22 LEGS (M, N, and O). Cover the holes with three HOLE PLUGS (41P). å Make adjustments before covering the holes. With your No. 2 Phillips Screwdriver, turn the ADJUSTABLE FOOT downward until it touches the fl oor. Floor Page 22 420408 www.sauder.com/services...
  • Página 23 Separate the CARDS on the CARD SHEET (38M) and å insert one into the CARD HOLDER (35M). Repeat this step using the remaining LARGE å ADJUSTABLE SHELF and MOLDING. SILVER 5/8" MACHINE SCREW (4 used for the CARD HOLDERS) Open end to insert CARDS www.sauder.com/services 420408 Page 23...
  • Página 24 This completes assembly. Clean with a damp cloth. Wipe dry. å And to celebrate, why not share your success story? 25 lbs. 135 lbs. 25 lbs. 25 lbs. 75 lbs. total 25 lbs. (6 used) (16 used) To cover HIDDEN CAMS Page 24 420408 www.sauder.com/services...
  • Página 25: Liste De Pièces

    QUANTITÉ d’ a chat de cet élément et conserver le livret pour future référence. EXTRÉMITÉ DROITE ..........1 14H CHARNIÈRE INCURVÉE .........4 Pour contacter Sauder EXTRÉMITÉ GAUCHE ..........1 40H CHARNIÈRE ..............4 en ce qui concerne cet MONTANT................1 ARRÊT DE PORTE ............4 élément, faire référence...
  • Página 26 Fixer les MONTANTS (C, D et E) au DESSUS (F). Serrer six diagramme ci-dessous avant de commencer l'assemblage ! FIXATIONS TWIST-LOCK®. • Cette unité Sauder est conçue pour les téléviseurs pesant moins Utilisation de la FIXATION TWIST-LOCK® SAUDER de 61 kg. Ne jamais utiliser avec des téléviseurs plus lourds.
  • Página 27 Fixer un BOUTON (28K) à la PORTE EN VERRE (J). Utiliser une le MONTANT (C). VIS À MÉTAUX 38 mm ARGENTÉE (95S). Répéter cette étape pour fi xer l'autre PORTE EN VERRE (J) au MONTANT GAUCHE (E). Voir l'étape suivante pour réglages des PORTES. www.sauder.com/services 420408 Page 27...
  • Página 28 Couvrir les trous avec trois CACHE-TROUS (41P). sur les GOUPILLES EN MÉTAL. REMARQUE : Prière de lire les informations importantes sur la sécurité fi gurant sur les pages arrière du manuel d’instructions. Ceci complète l'assemblage. Nettoyer avec un tissu humide. Essuyer. Page 28 420408 www.sauder.com/services...
  • Página 29: Lista De Partes

    EXTREMO DERECHO ..........1 14H BISAGRA CURVADA ..........4 et conserver le livret 40H BISAGRA ................4 EXTREMO IZQUIERDO ..........1 pour future référence. Pour contacter Sauder TOPE DE PUERTA ............4 PARAL ...................1 en ce qui concerne cet 28K POMO ..................4 PARAL DERECHO ............1 élément, faire référence...
  • Página 30 - antes de comenzar el ensamblaje! Cómo utilizar el SUJETADOR TWIST-LOCK® SAUDER • Esta unidad Sauder está diseñada para ser usada con televisores cuyo peso sea inferior a 61 Kg. Nunca la use para un 1. Inserte el extremo con cabilla del SUJETADOR en el agujero de televisor de mayor peso.
  • Página 31 DERECHO (E y D) y dos TOPES DE PUERTA (4I) en el PARAL (C). Repita este paso para fi jar la otra PUERTA DE VIDRIO (J) al PARAL IZQUIERDO (E). Consulte el próximo paso para ajustar la PUERTA. www.sauder.com/services 420408 Page 31...
  • Página 32 Cubrir los agujeros con tres TAPONES DE AGUJERO (41P). NOTA: Por favor, lea las páginas de atrás del folleto de instrucciones en cuanto a importante información de seguridad. Esto completa el ensamblaje. Limpiar con un trapo húmedo. Seque con un paño. Page 32 420408 www.sauder.com/services...
  • Página 33 équipé. • Blessure physique. Le mobilier peut être très lourd. • Ne pas pousser le mobilier, surtout sur la moquette. Se faire aider par une autre personne pour soulever l’élément et le mettre en place. www.sauder.com/services 420408 Page 33...
  • Página 34 • Lesión física. El mobiliario puede ser • No empuje la unidad, especialmente muy pesado. sobre un piso alfombrado. Pide la ayuda de otra persona en levantar la unidad y colocarla en lugar. Page 34 420408 www.sauder.com/services...
  • Página 35: Garantie Limitée De 5 Ans

    GARANTIE LIMITÉE DE 5 ANS 1. Sauder Woodworking Co. (Sauder®) off re une couverture de garantie limitée à l’ a cheteur 4. La présente garantie ne s’ a pplique qu’ a ux défauts garantis qui se produisent pour initial du présent produit pendant une période de cinq ans à...
  • Página 36 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.