EINHELL TC-PL 900 Manual De Instrucciones página 17

circumstances.
f) Wear suitable work clothes. Do not wear
loose clothing or jewellery. Keep hair, clo-
thes and gloves away from moving parts.
Loose clothing, jewellery or long hair can get
trapped in moving parts.
g) If vacuuming devices and draining de-
vices can be fi tted, make sure that these
are correctly attached and correctly used.
The use of a dust extraction system can redu-
ce the danger posed by dust.
4. Usage and treatment of the electric tool
a) Do not overload the appliance. Use the
correct tool for your work. You will be able
to work better and more safely within the gi-
ven performance boundaries.
b) Do not use an electric tool with a defec-
tive switch. An electric tool that cannot be
switched on or off is dangerous and must be
repaired.
c) Pull the plug out of the socket and/or
remove the battery before making any ad-
justments to the appliance, changing ac-
cessories or put the appliance down. This
safety measure prevents starting the electric
tool unintentionally.
d) Keep unused electric tools out of the
reach of children. Do not allow people
who are not familiar with the appliance or
who have not read these instructions to
use the appliance. Electric tools are dange-
rous if they are used by inexperienced people.
e) Clean your electric tool carefully. Check
whether moving parts are functioning
properly and not jamming, whether parts
are broken or damaged enough that the
functioning of this electric tool is aff ec-
ted. Damaged parts must be repaired be-
fore using the appliance. Many accidents
are caused by badly maintained electric tools.
f) Keep your cutting tools sharp and clean.
Carefully maintained cutting tools with sharp
cutting edges will jam less and are easier to
control.
g) Make sure to use electric tools, accesso-
ries, spare parts, etc. in accordance with
these instructions. Take the conditions
in your work area and the job to perform
into account. Using electric tools for any
purpose other than the one for which they are
intended can lead to dangerous situations.
Anl_SA_TC_PL_900_SPK8.indb 17 Anl_SA_TC_PL_900_SPK8.indb 17
GB
5. Service
a) Have your electric tool repaired only by
trained personnel and/or the authorized
service agent, using only genuine spare
parts. This will ensure that your electric tool
remains safe to use.
Special safety information
Always secure the workpiece if possible: Use
clamps or a vise to hold the workpiece securely.
This is far safer than holding it in your hand and
also means that you have both hands free to ope-
rate the electric tool.
Safety information for planes
•
Wait for the knife shaft to stop before you
put down the electric equipment. An expo-
sed rotating knife shaft can become caught
on the surface and result in loss of control
and serious injuries.
•
Hold the electric equipment only by the
insulated handles because the knife shaft
might strike the equipment's own power
cable. Contact with a live cable might also
make the metal parts of the equipment live
and cause an electric shock.
•
Use clamps or some other means to fas-
ten and secure the workpiece to a sturdy
surface. If you hold the workpiece only with
your hand or against your body it will remain
unstable and might cause you to lose control.
•
Ensure that there are no foreign objects
adhering to the workpiece in order to avoid
damaging the electric hand plane.
•
Hold the tool by its handle using both hands
and place the front base plate of the plane on
the workpiece. The base plates must evenly
rest on the workpiece during the planing pro-
cess.
•
Allow the tool to reach its maximum operating
speed before you start to plane.
•
Set the planing depth to 0 mm when you have
finished working.
•
Replace used planing knives with a set of
new knives when worn down.
•
Some types of planing knives have two bla-
des. When one blade has become blunt, the
planing knife can be turned over.
•
Blunt planing knives cannot be resharpened.
•
Always ensure that you replace both knives at
the same time.
•
Only the original, manufacturer-approved
knife block may be used for this electric hand
plane.
- 17 -
07.11.2019 10:27:49 07.11.2019 10:27:49