Personal Safety; Environmental Safety; Cleaning And Disposal - Black+Decker BDCRO20 Manual De Instrucciones

Lijadora excéntrica de 20 v máx
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
5) Battery Tool Use and Care
a ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
b ) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c ) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws, or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
d ) Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from
the battery may cause irritation or burns.
6) Service
a ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
SAFETY WARNINGS AND INSTRUCTIONS:
SANDERS

ALWAYS WEAR EYE PROTECTION.
Clean your tool out periodically.

WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the State
of California to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals
are:
-
lead from lead-based paints,
-
crystalline silica from bricks and cement and other
masonry products, and
-
arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sanding,
sawing, grinding, drilling, and other construction
activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into
your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.

CAUTION: Wear appropriate hearing protection
during use. Under some conditions and duration of
use, noise from this product may contribute to hearing
loss.
OTHER IMPORTANT SAFETY WARNINGS
AND INSTRUCTIONS
Sanding Lead based Paint
Sanding of lead based paint is NOT RECOMMENDED due
to the difficulty of controlling the contaminated dust.
The greatest danger of lead poisoning is to children and
pregnant women.
Since it is difficult to identify whether or not a paint contains
lead without a chemical analysis, we recommend the
following precautions when sanding any paint:

PERSONAL SAFETY

No children or pregnant women should enter the work
area where the paint sanding is being done until all
clean up is completed.
A dust mask or respirator should be worn by all persons
entering the work area. The filter should be replaced
daily or whenever the wearer has difficulty breathing.
nOTE: Only those dust masks suitable for working with lead
paint dust and fumes should be used. Ordinary painting
masks do not offer this protection. See your local hardware
dealer for the proper (NIOSH approved) mask.
NO EATING, DRINKING or SMOKING should be done in
the work area to prevent ingesting contaminated paint
particles. Workers should wash and clean up BEFORE
eating, drinking or smoking. Articles of food, drink, or
smoking should not be left in the work area where dust
would settle on them.

ENVIRONMENTAL SAFETY

Paint should be removed in such a manner as to
minimize the amount of dust generated.
Areas where paint removal is occurring should be sealed
with plastic sheeting of 4 mils thickness.
Sanding should be done in a manner to reduce tracking
of paint dust outside the work area.

CLEANING AND DISPOSAL

All surfaces in the work area should be vacuumed
and thoroughly cleaned daily for the duration of the
sanding project. Vacuum filter bags should be changed
frequently.
Plastic drop cloths should be gathered up and disposed
of along with any dust chips or other removal debris.
They should be placed in sealed refuse receptacles and
disposed of through regular trash pick-up procedures.
During clean up, children and pregnant women should
be kept away from the immediate work area.
All toys, washable furniture and utensils used by
children should be washed thoroughly before being
used again.
English
3

Publicidad

Tabla de contenido
loading

Tabla de contenido