Publicidad
Idiomas disponibles
Idiomas disponibles
General maintenance work
•
Check the appliance and accessories before each use for ob-
vious defects such as loose, worn or damaged parts. Replace
these if necessary.
•
Replace a blunt or bent blade or one which has been dam-
aged in some other way.
•
When performing maintenance work on the saw blades, such
as repair or regrinding, always follow the manufacturer's in-
structions.
Maintenance work and modifi cations to circular saw
blades should only be performed by a professional, i.e.
a person with specialist training and experience who is
familiar with the design requirements and the necessary
safety steps.
Storage
•
Store the appliance in a dry place well out of reach of
children.
Waste disposal and environmental
protection
Take the batteries out of the device and recycle the device, bat-
teries, accessories and packaging in an environmentally friendly
manner.
Electrical machines do not belong with domestic waste.
Directive 2012/19/EU on waste electrical and electronic equip-
ment: Used electrical devices must be collected separately for
disposal and recycled in an environmentally sound manner.
Depending on the implementation in national law, you may have
the following options:
• Return to a shop,
• Hand over to an offi cial collection point,
• Return to the manufacturer/distributor. We will dispose of any
defective devices that you send to us free of charge.
Trouble shooting
Problem
1. Blade dissolves after swit-
ching off the engine
2. Engine will not start
3. Motor wrong direction of
rotation
4. Motor will not work, the
fuse is activ
5. Fire marks on the cutting
surface
Possible cause
To slightly tightened fastening nut
a) Failure mains fuse
b) Defective extension cable
c) Connections on motor or switch not in order
d) Motor or switch faulty
Capacitor faulty
a) Cross section of the extension cable does not
suffi ciently
b) Overload by a blunt saw blade
a) blunt saw blade
b) wrong saw blade
This does not affect accessories enclosed with the old devices or
tools without any electrical components.
Take the device to a recycling plant. The plastic and metal parts
used on your device can be properly sorted according to mate-
rials and grades and effi ciently recycled. Please contact our ser-
vice centre for more information.
Defective or used batteries must be recycled in accordance with
Directive 2006/66/EC.
Dispose of batteries in a discharged state. We recommend cov-
ering the contacts with an adhesive strip to protect against short
circuits. Do not open the battery.
Dispose of the batteries according to local standards. Hand in the
batteries at a used battery collection point where they are recy-
cled in an environmentally friendly manner. For more information,
please contact your local waste management provider or our
service centre.
Spare parts/Accessories
Spare parts and accessories can be obtained at
www.grizzlytools.shop
If you have issues ordering, please use the contact form.
If you have any other questions, contact the "Service-Center"
(see page 46).
Blade guard, complete ............... Order-No. 91106125
(2)
Saw blade 24 Teeth ................... Order-No. 13800400
(4)
Saw blade 48 Teeth ................... Order-No. 13800409
(4)
Table width extender, complete .... Order-No. 91106128
(6)
Guide rail .................................. Order-No. 91106122
(7)
Scale ......................................... Order-No. 91106124
(8)
Handwheel, complete .................. Order-No. 91106129
(9)
(10) Base frame ................................. Order-No. 91106127
(16) Parallel stop ............................... Order-No. 91106121
(18) Push stick ................................... Order-No. 91104950
(28) Laser ......................................... Order-No. 91106126
(36) Transverse stop ........................... Order-No. 91106120
(h+i+k) Tool set ...................................... Order-No. 91106131
Hexagon socket wrench HX 6
Ring spanner AF 10/22
Open-ended spanner AF 8/10
Fault correction
Tighten the right hand thread nut
a) Check mains fuse
b) Replace extension cord
c) Repair by electrical specialist
d) Repair by electrical specialist
Repair by electrical specialist
a) see „Electrical connection"
b) Change saw blade
a) Sharpen or change saw blade
b) Change saw blade
GB
MT
45
Publicidad
