Publicidad
Idiomas disponibles
Idiomas disponibles
3. Fix the stop rail (35) by tightening the two knurled nuts (r).
4. Removal is carried out in reverse order.
Adjusting the scale of the parallel stop
24
(Fig.
)
Check whether the display on the sight glass (p) of the parallel
stop (16) shows the correct values with respect to the cutting line.
If this is not the case, please proceed as follows:
-
Release the screw (q) with which the display on the sight
glass (p) of the parallel stop (16) is attached. The sight glass
(p) display can now be set to the correct position.
-
Now, retighten screw (q) on the sight glass (p).
Transverse stop
25
(Fig.
)
-
Push the transverse stop (36) into a groove (33) of the saw
table.
-
Loosen the knurled screw (34).
-
Turn the transverse stop (36) until the desired angle is set. The
notch on the guide bar shows the angle that has been set.
-
Retighten the knurled screw (34).
Caution!
-
Do not push the stop rail (35) too far in the direction of the
saw blade.
-
The distance between the stop rail (35) and saw blade (4)
should be approximately 2 cm.
Angle Adjustment
25
3
(Fig.
+
)
With the table circular saw it is possible to make bevel cuts to
the left at an angle of 0° to 45° to the stop rail. Before each cut,
make sure that no collision is possible between the stop rail (35),
cross-cutting gauge and the saw blade (4).
-
Release the clamping screw (11)
-
Turn the handwheel (9) to set the desired angle on the scale
(8).
-
Lock the clamping srew (11) in the desired angular position.
Using the Laser
17
26
(Fig.
+
)
-
The laser (28) enables you to carry out precision cuts with
your circular saw.
-
The laser light is produced by a laser diode supplied by two
batteries. The laser light is expanded to form a line and is
emitted through the laser aperture (30). You can then use the
line as an optical marking for the cutting line of the precision
cut. Please note the laser safety information.
-
Switch on the laser: turn the laser on/off switch (29) to I.
When the saw blade guard (2) is mounted, the laser on/off
switch (29) is accessible through a recess in the guard (Fig.
). A red laser beam is now projected out of the laser exit
26
aperture (30). If you guide the laser beam along the cutting
line mark while sawing, you will achieve clean cuts.
-
Switch the laser off: turn the laser on/off switch (29) to 0. The
laser beam goes off. Please always turn the laser off when it
is not required in order to save the batteries.
-
The laser beam may be blocked by dust deposits and chips.
You should therefore remove these particles from the laser exit
aperture after every use (with the device switched off).
Adjusting the Laser
17
(Fig.
)
If the laser (28) no longer shows the correct cutting line, this can
be readjusted.
1. To do this, open the screws (z).
2. Adjust the laser so that the laser beam hits the cutting teeth of
the saw blade (4).
3. Retighten the screws (z) alternately and evenly.
Use
Working Instructions
After each new adjustment, we recommend a trial cut in order to
check the set dimensions. After the saw has been switched on,
wait until the saw blade has reached its maximum speed before
you carry out the cut.
Secure long workpieces against tilting at the end of the cutting
process (e.g. unwinding stand etc.)
Only use saw blades with a rotational speed that is equal to or
higher than the rotational speed indicated on the power tool.
Caution with incision cutting.
Operate the device only with a suction system. Check and clean
the suction channels regularly.
Suitability of the saw blades:
-
24 teeth: soft materials, high chip removal, rough cut image
-
48 teeth: hard materials, lower chip removal, fi ner cut image
Performing Longitudinal Cuts
28
(Fig.
)
Here, a workpiece is cut in its longitudinal direction. One edge of
the workpiece is pressed against the parallel stop (16) while the
fl at side lies on the saw table (1). The saw blade guard (2) must
always be lowered onto the workpiece. The working position dur-
ing longitudinal cutting must never be in a straight line with the
cutting line.
-
Adjust the parallel stop (16) according to the workpiece
height and the desired width.
-
Switch on the saw.
-
Place your hands with the fi ngers closed together fl at on the
workpiece and push the workpiece along the parallel stop
(16) into the saw blade (4).
-
Guide from the side with your left or right hand (depending
on the position of the parallel stop) only up to the front edge
of the saw blade guard (2).
-
Always push the workpiece through to the end of the riving
knife (3).
-
The cutting waste remains on the saw table (1) until the saw
blade (4) is back in its resting position.
-
Secure long workpieces against tilting at the end of the cut-
ting process! (e.g. unwinding stand etc.)
Cutting narrow Workpieces
29
(Fig.
)
Longitudinal cuts of workpieces with a width of less than 120 mm
always have to be cut with the help of a push stick (18). The push
stick is included in the scope of delivery. Replace a worn or dam-
aged push immediately.
•
Adjust the parallel stop (16) according to the planned work-
piece width.
GB
MT
43
Publicidad
