Publicidad
Idiomas disponibles
Idiomas disponibles
ATTENTION!
The following information is for the NX25‑240B series pumps and meters (designed for use outside the United States and Canada)! Refer to the information label applied to your
pump to see if it is applicable.
Materials of Construction
Materials of construction of the external surface of the unit are: plated steel
painted cast iron, plated powdered metal, painted aluminum, thermo‑plastic,
anodized aluminum.
Materials of construction of the wetted parts are: cast iron, coated steel, stainless steel,
fluorocarbon, nitrile, cork, powdered metal, thermo‑set plastic, thermo‑plastic, ceramic.
Repair and Maintenance
Contact the place of purchase for warranty repair and maintenance.
Specific Conditions of Use
• Consult the manufacturer for information on the dimensions of the flameproof
joints if necessary.
• The special fasteners used a securing bolts for the end bell are made of Class 12.9
type fasteners. The special fasteners used for the cover plate attachment are made
of Class I0.9 type fasteners.
Installation
Pump must be installed in compliance with EN 60079‑14 or IEC 60079‑14,
as applicable.
Certificates for Compliance of Safety have been obtained from the following agencies
for products sold outside the US and Canada. Please refer to the tag on your particular
product for its particular compliance data.
The following standards were used to show compliance in the European Union:
EN IEC 60079‑0:2018, Ed 7 "Explosive atmospheres
General requirements."
EN 60079‑1:2014, Ed 7 "Explosive atmospheres – Part 1: Equipment protection
by flameproof enclosures "d"."
EN ISO 80079‑36:2016, Ed 1 "Explosive atmospheres – Part 36: Non‑electrical
equipment for explosive atmospheres – Basic method and requirements."
EN ISO 80079‑37:2016, Ed 1 "Explosive atmospheres – Part 37: Non‑electrical
equipment for explosive atmospheres – Non electrical type of protection
constructional safety "c", control of ignition source "b", liquid immersion "k"."
Part 0: Equipment –
–
Fill-Rite Company
8825 Aviation Drive
Fort Wayne, Indiana 46809 USA
T 1 (800) 720‑5192
1 (260) 747‑7524
F 1 (800) 866‑4681
fillrite.com | sotera.com | gormanrupp.com
Directive 2014/34/EU – "Equipment and protective systems intended for use in
potentially explosive atmospheres."
Directive 2011/65/EU – "Restrictions of the use of certain hazardous substances in
electrical and electronic equipment."
2006/42/EC ‑ "Machinery."
ISO 12100:2010 ‑ "Safety of machinery ‑ General principles for design ‑ Risk assessment
and risk reduction."
BS EN 809:1998+A1:2009 ‑ "Pumps and pump units for liquids. Common
safety requirements."
The following standards were used to show compliance for IECEx certification:
IEC 60079‑0:2017, Ed 7
IEC 60079‑1:2014, Ed 7
Motor Plate Information
MODEL: NX25‑240B
VOLT: 230AC
HP: 1/3
1.8 AMP
CONTINUOUS DUTY
RPM:3500
OPERATING TEMP T6
‑40° C ≤ Ta ≤ +40° C
INS:B
SEE INSTALLATION DOCUMENT INSTRUCTION
CE2809
SERIAL # AND MANUFACTURING DATE
Fill‑Rite Trademark
8825 Aviation Drive
Fort Wayne, IN 46809 USA
2809
II 2 G
Ex db IIA T6 Gb
UL 21 ATEX 2262X Rev. 0.
IECEx 21.0031X ISSUE 0.
Ex db IIA T6 Gb
FIL-MN-437v.3
Publicidad
