Descargar Imprimir esta página

Scheppach PL55 Traduccion Del Manual De Instrucciones Originale página 33

Sierra de incisión

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 87
m Warning! Risk of injury! Electric shock
Always pull the mains plug out of the socket before per-
forming any type of work on the machine!
1.
Press the plunge trigger (3), bring the saw blade
into the blade-change position (Adjustment screw
for depth of cut (7) shall be adjusted to 25 mm) and
insert the hex wrench into the saw blade locking
screw (19).
2.
Press on the shaft lock (18) and rotate the saw
blade (15) until the lock clicks into place.
3.
Hold down the locking shaft (18) and open the saw
blade locking screw (19) counter clockwise, while
keeping the blade in the blade-changing position.
4.
Remove the outer flange (20) and the saw blade
(15).
m Caution! Risk of injury!
Wear protective gloves
5.
Insert the new blade and outer flange (20).
6.
Screw in and tighten the saw blade locking screw
(19) while keeping the shaft locking mechanism
pressed again.
7.
Set the plunge saw to its original position (0°).
Adjusting the riving knife (16) (Fig. A + K)
Adjust the distance between saw blade (15) and riving
knife (16) after a saw blade replacement, or whenever
necessary.
Put the saw in the same position as you do when re-
placing a saw blade.
Unfasten the adjustment screw for riving knife (17) us-
ing an Allen key and set the riving knife (16) 2-3 mm
higher than the saw blade, then re-tighten the adjust-
ment screw for riving knife (17).
Connecting extraction device
A normal household vacuum cleaner is not a suitable
extraction device.
A extraction device with an extractor hose diameter of
38 mm (38 mm recommended due to the reduced risk
of clogging) can be connected to the extractor connec-
tor (1).
m Warning! Dust hazard
Dust can be hazardous to health. Always work with a
dust extractor.
Always read applicable national regulations before ex-
tracting hazardous dust.
9.
Commissioning
m Warning! Risk of injury!
Improper assembly of the plunge saw can result in se-
rious injury.
• Before switching the plunge saw on, make sure
the saw blade is correctly mounted and that mobile
parts can move freely.
After switching on the saw, you must wait until the saw
blade (15) has reached the maximum speed before you
perform the cut.
Switching the plunge saw on and off
• To switch on the plunge saw, press the ON/OFF
switch (8). The motor will start.
• To switch off the plunge saw, release the ON/OFF
switch (8).
After having performed all the above procedures and
operations, you may begin cutting.
m Caution!
Always keep hands away from the cutting area and do
not try to approach it when the machine is running.
Working with the machine
m ATTENTION! Please observe all mentioned safety
informations and the following rules when working:
• Only guide the machine against the workpiece when
it is switched on.
• Always secure the workpiece in such a manner that
it cannot move while being processed.
• Always push the machine forwards, never draw the
machine towards yourself.
• Adapt the fast-feed speed to prevent the cutters on
the saw blade from overheating and prevent plastic
materials from melting during cutting.
• For work that generates dust, wear a dust mask.
• Grip the saw tightly with both hands ensuring that
one hand is placed on the main handle and the other
on the front handle.
• When using a guide rail, it must be fastened with
screw clamps.
• Make sure the power cable is not placed in the saw-
ing direction.
Sawing along the scribe mark
The cutting indicator (Fig. G Pos. G1) displays the cut-
ting line for 0° and 45° cuts (without guide rail).
www.scheppach.com
GB | 33

Publicidad

loading

Este manual también es adecuado para:

5901802915