Virutex FR277R Manual De Instrucciones página 8

with a triggering current of 30 mA maximum.
• Wires of the extension cable must have a minimum
section of 1,5 mm2 and the cable must be fully unwound.
• Plug in the tool only if the switch is turned off.
• Always wear personal protective equipment, glasses
and footwear.
• Always hold the router with both hands.
• Switch off the motor after you have finished milling.
• Before you put down the tool, loosen the router table.
• Always put down the tool on a horizontal and clean
surface.
• Do not put any other tools on the workpiece.
• Workpiece must be clean, without any rests of ma-
terials, sawdust...
• Work place should have adequte lights, it is forbiidden
to use the tool in rooms with inflammable substances
and gases, switch on/off the tool only by the switch and
not by disconnesting the plug.
• Be careful of screws, nails and other objects in the
workpiece while milling.
• Start working only when the tool has reached full speed.
• Be aware of the sudden impact when the FR277R and
FR278R power tool is switched on.
• Prevent unintentional switching on of the tool.
• Always use undamaged and sharp router bits.
• When you do not use the tool, store it in a dry place
protected from dust.
• Do not wear loose clothes of jewelry the tool could
take hold of and pull it towards it. If you have long hair,
wear a protective head-covering. When working outside,
wear non-skid footwear.
• In case the tool is blocked, immediately switch off the
tool and disconnect the plug.
• Clamp the workpiece.
• Guide only switched on tool towards the workpice.
Switch off the tool when you when you have lifted the
tool from the workpiece.
• Use only original parts and accessories.
4. PACKAGE CONTENTS
Router
Parallel guide
Compass
Wrench
Dust extraction adapter
Instructions for use, guarantee card
5. PREPARING THE TOOL FOR MILLING
Always disconnect the plug from power
source before making any adjustments
or changing any accessory.
8
6. DUST SUCTION
Milling and grinding wood generate sawdust and dust
that endanger safety and health. Using dust suction
prevents air pollution for breathing and makes easier
removal of wastes.
7. MOUNTING DUST EXTRACTION ADAPTER
Put the dust extraction adapter 15 (Fig. 2) baseplate 3
(Fig. 2) so that the twin column guide A (Fig. 2) is inside
the mouth of the dust extraction adapter.
Push the mouth with the right hand thumb in the
direction A (Fig. 2) towards the locking edge C so that
the lock D on the periphery is automatically cought in
the edge B (Fig. 2)
Connect the hose of a vacuum cleaner directly to the
dust extraction adapter 15 (Fig. 3), or connect it with a
suction hose with a turning connection for extracting
dust 4 (Fig. 3).
Fix the latter into the corresponding place below the
motor cover.
Mount the upper dust extraction adapter by pushing
it in the directions C until it snaps between the motor
gerabox and the motor cover. Then attach the lower
part of the hose to the dust extraction adapter 15 in
the direction D (Fig. 3).
Turning connection enables better view of the milling
area and setting the vacuum cleaner hose in the most
favourable position. The diameter of the dust extrac-
tion adapter is 35 mm, which corresponds to hoses of
standard vacuum cleaners.
Using STANDARD DUST COLLECTOR ATTACHMENT
Ref.6446073 (optional), the router may be connected
to our AS182K, AS282K, AS382L aspirator or to any
other industrial aspirator via the aspiration connector.
8. REMOVING UPPER DUST
EXTRACTION ADAPTERS (Fig. 3)
With the hose can be removed by first taking off the hose
from the dust extraction adapter 15 in the direction E,
and then push with the left hand thumb the upper part
of the dust extraction adapter in the direction F (Fig. 3).
9. REMOVING LOWER DUST
EXTRACTION ADAPTERS (Fig. 2)
Take off the hose of the dust extraction adapter 4. Press
the lock D on the periphery of the adapter 15 that much
to release it and push in the direction of the arrow B.
Then take off the adapter (Fig. 2)
10. CHOOSING A ROUTER