Publicidad
Idiomas disponibles
Idiomas disponibles
Compressor Delay Protection
To protect the compressor, apart from when the appliance and compressor are activated for the
first time after being turned on via the power button, there will be a three-minute delay between
every occurrence of the compressor turning off and on.
TROUBLESHOOTING
― ―
We do everything that we can to ensure our products are easy to install and use. If you do have
any issues, here are some troubleshooting tips that may help you to solve the problem. If the
problem persists, please contact our customer service team at help@probreeze.com
Problem
Cause
No power.
The unit will pause if the water
tank is full. FL will show on the
display panel.
If TIMER off has been
activated, the appliance
cannot be turned on for 3
The appliance is not
minutes.
operating.
For your safety, the device
will pause if the internal
components drop below 8°C
(46.4°F).
The device will stop if the
temperature target has been
hit.
Doors and windows are
open or there are other heat
sources impacting the room
temperature.
Warm air is entering the room
from the exhaust hose.
The appliance is not cooling
effectively.
Filters are blocked.
Air inlet or air outlet is
clogged.
22 of 76 | English
Solution
Connect the unit to a live
power socket and turn it on.
Empty the water tank or
connect the drainage hose as
per instructions above.
Wait for three minutes and try
to turn your device on.
Wait for 5 minutes. The
device will activate the safety
features and will resume
when the temperature has
normalised.
Decrease the temperature
target using the increase/
decrease button to re-
activate the device.
Close all doors and windows
or attach seals as per
instructions. Remove all
sources of heat from the
room.
Position your unit close to a
window or door and ensure
they are sealed with the
exhaust hose outside of the
room.
Clean filters as per
instructions above.
Check for obstructions and
clean the inlets or outlets.
The device is too noisy.
Noise is natural for air
conditioners as they pump
refrigerant around the unit to
cool the air. If your appliance
is making an unusual noise it
may be due to it being on an
uneven surface.
Not enough water is being
Dehumidifiers draw air in and
collected.
condense it on a cold surface
to remove the moisture. If
the surrounding air is too
cold, their effective- ness is
reduced.
Display showing E1.
Pipe temperature sensor
failure.
Display showing E2.
Room temperature sensor
failure.
Display showing E4.
Anti-frost protection.
FCC STATEMENT
― ―
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE
FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Check that your device is on
a flat, secure surface.
For best results,
dehumidifying mode is
best used in warm, humid
temperatures.
Arrange for a professional to
check the pipe temperature
sensor and related circuits.
Arrange for a professional to
check the room temperature
sensor and related circuits.
Appliance returns to
operating at chosen settings
once the internal pipe
temperature exceeds 8°C
(46.4°F)
English | 23 of 76
Publicidad
