Publicidad
Idiomas disponibles
Idiomas disponibles
1. Slide the selector switch to expose the single
nail icon
.
2. Fully depress nosepiece against the work surface (motor
will start).
3. Pull trigger (nail will drive into work surface).
4. Release trigger.
5. Lift nosepiece off work surface.
6. Repeat steps 2 through 4 for next application.
NOTICE: The contact trip needs to be depressed followed by
a trigger pull for each nail followed by a release of both the
contact trip and trigger after each nail.
Bump Action
(Fig. F)
Bump action is intended for rapid nailing on flat, stationary
surfaces and typically most effective for applications that
require driving shorter nails.
When the tool is set in the bump actuation mode, two
methods of tool operation are available: place actuation
and bump actuation.
Slide the selector switch to expose the triple nail icon
To operate the tool using the place actuation method:
WARNING: A nail will fire each time the
trigger is depressed as long as the contact trip
remains depressed.
1. Depress the contact trip against the work surface.
2. Depress the trigger.
To operate the tool using the bump
actuation method:
1. Depress the trigger.
2. Push the contact trip against the work surface. As long
as the trigger is depressed, the tool will fire a nail every
time the contact trip is depressed. This allows the user
to drive multiple nails in sequence.
WARNING: Do not keep trigger depressed when tool
is not in use. Keep the trigger lock-off in the locked
position when the tool is not in use.
WARNING: When the tool's motor is running, pulling
the trigger or depressing the contact trip will cause a
nail to fire.
Preparing the Tool
WARNING: NEVER spray or in any other way apply
lubricants or cleaning solvents inside the tool. This can
seriously affect the life and performance of the tool.
nOTE: The battery pack is not fully charged out
of the carton. Follow instructions outlined (see
Charging Procedures).
1. Read the Safety Instruction section of this manual.
2. Wear eye and ear protection.
3. Ensure magazine is empty of all fasteners.
4. Check for smooth and proper operation of contact
trip and pusher assemblies. Do not use tool if either
assembly is not functioning properly. NEVER use
a tool that has the contact trip restrained in the
actuated position.
5. Keep tool pointed away from yourself and others.
6. Insert fully charged battery pack.
Using the Trigger Lock-off (Fig. G)
WARNING: To reduce the risk of serious personal
injury, do not keep trigger depressed when tool is not
in use. Keep the trigger lock-off switch LOCKED (Fig. G)
when the tool is not in use.
WARNING: To reduce the risk of serious personal
injury, lock off trigger, disconnect battery pack
from tool and remove nails from magazine before
making adjustments.
Each D
WALT nailer is equipped with a trigger lock-off
e
which when pushed to the right as shown in Figure G,
prevents the tool from firing a nail by locking the trigger and
bypassing power to the motor.
When the trigger lock-off is pressed to the left, the tool will
be fully operational. The trigger lock-off should always be
locked off whenever any adjustments are made or when
tool is not in immediate use.
NOTICE: Do not store tool with battery pack installed. To
.
prevent damage to the pack and to ensure best battery
life, store battery packs out of the tool or charger in a cool,
dry ocation.
Fig. G
2
Loading the Tool (Fig. H)
WARNING: Keep the tool pointed away from yourself
and others. Serious personal injury may result.
WARNING: Never load nails with the contact trip or
trigger activated. Personal injury may result.
WARNING: Always remove battery pack before
loading or unloading nails. Serious personal injury
may result.
Load and Draw Method
1. Insert fasteners into the rear of the magazine
2. Pull pusher
8
back until the nail follower falls behind
the nails.
3. Release the pusher.
CAUTION: Keep fingers clear of pusher to
prevent injury.
English
2
.
7
11
Publicidad
