Descargar Imprimir esta página

Milwaukee 2722-20 Manual Del Operador página 4

Ocultar thumbs Ver también para 2722-20:

Publicidad

Idiomas disponibles

Idiomas disponibles

ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always lock the trigger or remove
WARNING
the battery pack any time the tool
is not in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Selecting a Blade
The Quik-Lok
blade clamp can be used with all 1/2"
®
shank universal Sawzall
Sawzall
blades for best performance. When select-
®
ing a blade, choose the right type and length. Many
types of blades are available for a variety of appli-
cations: cutting metal, wood, nail-embedded wood,
scroll cutting, roughing-in, and contours.
Many lengths are also available. Choose a length
long enough to extend beyond the shoe and your
work throughout the stroke. Do not use blades less
than 3-1/2" long since they won't extend beyond
the shoe throughout the stroke.
Installing and Removing Blades from the
Quik-Lok
WARNING! Remove battery to avoid starting the
tool when changing blades. Make sure the spindle
and blade clamp areas are clean. Metal chips and
sawdust may prevent the Quik-Lok
from clamping securely.
1. Depending on the job,
the blade may be in-
serted with the teeth
facing up or down. To
install a blade, twist
collar in the direction
of the arrow while in-
serting the blade into
the clamp until the
tang butts against the collar.
2. Release collar and the spring loaded mechanism
will clamp the blade firmly in place.
3. Twist collar in the opposite direction of the arrow
to ensure that the blade is locked into the clamp.
4. Tug on blade to make sure it is securely locked in place.
5. To remove a blade, twist collar in the direction of
the arrow while pulling on the blade. Be careful
when handling hot blades.
blades. Use MILWAUKEE
®
Blade Clamp
®
blade clamp
®
Collar
Blade
Quik-Lok
Blade Clamp Maintenance
®
• Periodically clean dust and debris from the Quik-Lok
blade clamp with dry compressed air.
• If the collar resists twisting, twist it back and forth to
shake debris loose.
• Periodically lubricate Quik-Lok
dry lubricant such as graphite.
Removing Broken Blades from the
Quik-Lok
WARNING! Remove battery to avoid starting the
tool when removing blades. Broken blades can be
removed by the following methods.
• Point the tool downward, twist the collar, and shake
the tool up and down (do not turn the tool on while your
fingers are holding the blade clamp open). The shank
of the broken blade should drop out of the clamp.
• If shaking the tool doesn't work:
In most cases, a corner of the broken blade will extend
beyond the blade clamp. Simply twist the collar and
pull the broken blade out of the clamp by this corner.
• If the broken stub doesn't extend far enough to be
grabbed by its corner, use a thin blade with small
teeth (such as a metal cutting blade) to hook the
blade that is jammed in the clamp while twisting the
collar and pull it out.
To reduce the risk of injury, be sure
WARNING
the blade always extends beyond the
shoe and workpiece throughout the stroke. Blades
may shatter if they impact the workpiece or shoe.
Stroke
Stroke
4
blade clamp with
®
Blade Clamp
®
®

Publicidad

loading