Milwaukee DYMODRILLS 4004 Manual Del Operador página 14

For a complete listing of accessories refer to your MILWAUKEE Electric Tool catalog or go on-line to www.mil-electric-tool.com. To obtain a catalog,
contact your local distributor or a service center listed on the back cover of this operator's manual.
Meter Boxes
Cat. No. 48-51-0100 (30 amp, 120 volt)
(Not available in Canada)
Same as supplied with Vac-U-Rig
with Cat. No. 4136. Ammeter and power switch appear on the front
panel and a single 20 amp twist lock receptacle for the drill motor and
two convenience outlets are on the back of the box.
Meter Boxes
Cat. No. 48-51-0120 (20 amp, 120 volt)
(Can be used in Canada)
Ammeter and power switch appear on the front panel with a single 20
amp twist lock receptacle for the drill motor on the back.
Telescoping Extension Assembly
Cat. No. 49-95-1000
This assembly braces the rig between the floor and ceiling for maximum
rigidity. It adjusts for 14-foot ceilings and features fixed hole adjust-
ments.
Copper Washer
Cat. No. 45-88-8565
Before using the tool, slip this washer onto the spindle to prevent the bit
from seizing on spindle during coring.
Spacer Assembly
Cat. No. 49-67-0110
For use with Cat. Nos. 4125 and 4130. Mounts between cradle and
Dymodrill motor when using 10" - 14" coring bits.
Spacer Assembly
Cat. No. 49-67-0115
For use with Cat. No. 4115 and 4120. Mounts between cradle and
Dymodrill motor when using 10" - 14" coring bits.
Water Collecting Ring
Cat. No. 48-70-0060
For use where water flow from coring must be trapped and drained.
Dike-type collector ring holds water for fast disposal when used with
bits up to 10" in diameter. A built-in vacuum hose fitting also allows the
ring to be used with a wet/dry vacuum cleaner.
Water Hose
Cat. No. 49-18-0055
This 8-foot water hose features a 5/8" coupling and standard brass
male and female water hose fittings.
Water Tank
Cat. No. 49-76-0055
This 3-1/2 gallon heavy-duty, impact-resistant poly tank is for use where
a regular tap water supply is not available.
Vacuum Pad Assembly (Single Pad)
Cat. No. 49-22-7100
This single vacuum pad is the same as supplied with Vac-U-Rig
ment Kit No. 49-22-7075. Can be used with Cat. Nos. 4115, 4125 and
4130.
Vacuum Pump Assembly (115 Volts)
Cat. No. 49-50-0160
This heavy-duty 1/8 H.P. pump comes complete with vacuum gauge, air
filter and cord. May be mounted to the base of the unit. Same as fur-
®
nished with Vac-U-Rig 49-22-7075. Can be used with Cat. Nos. 4115,
4125 and 4130.
page 14
To reduce the risk of injury, always unplug the tool before attaching
or removing accessories. Use only specifically recommended acces-
sories. Others may be hazardous.
® Attachment Kit No. 49-22-7075 and
®
ACCESSORIES
WARNING!
Vacuum Pump Assembly (115 Volts)
Cat. No. 49-50-0165
This heavy-duty 1/8 H.P. pump comes complete with vacuum gauge, air
filter and cord. May be mounted to the base of the unit. Can be used with
Cat. No. 4120.
Vac-U-Rig® Attachment Kit (115 Volts)
Cat. No. 49-22-7065
This kit includes: (1) vacuum pad; (1) vacuum pump assembly with
gauge, filter, 8-foot air hose, and fittings. Can be used with Cat. No.
4120.
Vac-U-Rig® Attachment Kit
Cat. No. 49-22-7075
This kit includes: (1) vacuum pad; (1) vacuum pump assembly with
gauge, filter, 8-foot air hose, and fittings. Can be used with Cat. Nos.
4115, 4125 & 4130.
Threaded Adapter
Cat. No. 48-04-0160
Thread Adapter reduces the thread size of 1-1/4"-7 to 5/8"-11
MILWAUKEE Dymobits and extensions.
Shear Pin No. 44-60-0065 (Low Strength Shear Pin)
Shear Pin No. 44-60-0032* (High Strength Shear Pin)
* (Standard equipment on Dymodrills except clutch Cat. Nos. 4004, 4005,
4092, 4206 and 4097).
9" Bit Extension
Cat. No. 48-95-1500
Extension threaded on both ends with a 1-1/4"-7 thread. For use with
Diamond Core Bits over 2" in diameter and a 1-1/4"-7 thread. Extension
mounts directly to the Dymodrill. Two or more extensions can be used
together to core deep holes.
10-1/2" Bit Extension
Cat. No. 48-95-2100
Extension threaded on both ends with a 5/8"-11 thread. For use with 1-1/4"
and 1-1/2" diameter Diamond Core Bits with a 5/8"-11 thread. Extension
requires Threaded Adapter No. 48-04-0160 for mounting to Dymodrills.
Two or more extensions can be used together to core deep holes.
3/16" Socket Wrench
Cat. No. 49-96-0085
Use to mount Dymodrills onto the cradle on Dymorigs
1-3/8" Open End Wrench
Cat. No. 49-96-4700
Use to install bits onto Dymodrills.
Vacuum Pad Gasket
Cat. No. 43-44-0570
Replacement part for vacuum pads on Cat. Nos. 4115, 4125 & 4130
Vacuum Base Gasket
Attach-
Cat. No. 43-44-0605
Replacement part for vacuum base Cat. No. 4120.
Rubber Cement
Cat. No. 44-22-0060
Use to bond vacuum pad gaskets to vacuum pads on Cat. Nos. 4115,
4120, 4125 and 4130.
Type "E" Grease
Cat. No. 49-08-4122
Use for lubricating rack and pinion as well as spindle.