Publicidad
Idiomas disponibles
Idiomas disponibles
BLUETOOTH®
Bluetooth mode settings
1
Press and hold
.
2
Turn the volume knob to select [BLUETOOTH], then press the knob.
3
Turn the volume knob to select an item (see the following table), then press
the knob.
4
3
Repeat step
until the desired item is selected/activated or follow the
instructions stated on the selected item.
5
Press
to exit.
To return to the previous setting item, press
1
PHONE*
Selects the phone or audio device to connect or disconnect.
" " appears in front of the device name when connected.
1
AUDIO*
1
APPLICATION*
Shows the connected phone name using the JVC Smart Music Control *
" " appears in front of the device name when connected.
1 Turn the volume knob to select a device to delete, then press the knob.
DELETE PAIR
2 Turn the volume knob to select [YES] or [NO], then press the knob.
SET PINCODE
Changes the PIN code (up to 6 digits).
1 Turn the volume knob to select a number.
(0000)
2 Press
1
Repeat steps
3 Press the volume knob to confirm.
AUTO CNNCT
ON: The unit automatically reconnect when the last connected Bluetooth device is
within range. ; OFF: Cancels.
AUTO PAIR
ON: The unit automatically pair supported Bluetooth device (iPhone/ iPod touch/
Android device) when it is connected through USB input terminal. Depending on the
operating system of the connected device, this function may not work. ; OFF: Cancels.
INITIALIZE
YES: Initializes all the Bluetooth settings (including stored pairing, phonebook, and
etc.). ; NO: Cancels.
INFORMATION
MY BT NAME: Displays the unit name (JVC UNIT). ;
MY ADDRESS: Shows address of this unit.
*
1
You can only connect a maximum of two Bluetooth phones and one Bluetooth audio device at any time.
*
2
JVC Smart Music Control is designed to view JVC car receiver status and perform simple control
operations on Android smart phones.
For JVC Smart Music Control operations, visit JVC website: <http://www.jvc.net/cs/car/>.
.
to move the entry position.
2
and
until you finish entering the PIN code.
Bluetooth compatibility check mode
You can check the connectivity of the supported profile
between the Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1
Press and hold
"BLUETOOTH"
USING PHONE"
2
Search and select "JVC UNIT" on the Bluetooth device
within 3 minutes.
Default: XX
3
Perform (A), (B) or (C) depending on what appears on the
display.
(A) "PAIRING"
the same passkey appears on the unit and Bluetooth
2
app.
device, then operate the Bluetooth device to confirm the
passkey.
(B) "PAIRING"
Bluetooth device.
(C) "PAIRING": Operate the Bluetooth device to confirm
pairing.
After pairing is successful, "PAIRING OK"
appears and Bluetooth compatibility check starts.
If "CONNECT NOW USING PHONE" appears, operate the
Bluetooth device to allow phonebook access to continue.
"TESTING" flashes on the display.
The connectivity result flashes on the display.
"PAIRING OK" and/or "H.FREE OK"*
and/or "PBAP OK"*
*
1
Compatible with Hands-Free Profile (HFP)
*
2
Compatible with Advanced Audio Distribution Profile (A2DP)
*
3
Compatible with Phonebook Access profile (PBAP)
After 30 seconds, "PAIRING DELETED" appears to indicate that
pairing has been deleted, and the unit exits check mode.
• To cancel, press and hold
then turn on the power again.
.
"CHECK MODE" appears. "SEARCH NOW
"PIN IS 0000" scrolls on the display.
"XXXXXX" (6-digit passkey): Ensure that
"PIN IS 0000": Enter "0000" on the
"[Device Name]"
1
and/or "A.STREAM OK"*
3
: Compatible
to turn off the power,
ENGLISH
2
15
Publicidad
