Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
INSTALLATION INSTRUCTIONS
PASSAGE
CUSTOM SHOWER WALL SYSTEM
™
MODELS: P2971SWT, P2974BWT
Visit http://www.americanstandard-us.com/passage-collection for coordinating products.
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
BEFORE YOU BEGIN....
Local building codes vary by location. Observe all local plumbing and building codes.
Unpack your new shower walls and inspect them carefully for damage. Verify that the walls are the correct size for your
installation. Refer to American Standard roughing-in information in the spec page for specific dimensions for each model.
NOTE: Take extra care in handling the front surfaces of the walls. Use only non-abrasive cloths to avoid scratching.
TOOLS:
Notched Trowel
Tape Measure
Pencil
Drill
Caulking Gun
Hole Saw or
Level
Square
Circular Saw
PREPARATION:
Must be installed over SHEETROCK/GREENBOARD or CEMENT/CONCRETE.
Illustration 1
A) WALL SURFACE PREPARATION
Ensure wall surface is dry, smooth, and free of dust, soap
scum, mold or other contaminants. Wipe wall surfaces with
a damp cloth and allow to dry.
Wall surface must be dry before panels can be applied.
Ensure that alcove is plumb and square. (Illustration 1)
INSTALLATION over OLD TILE
Rough up glossy tile surfaces using belt sander with
60-grit sandpaper.
Surface must be dry, smooth and free of any dust or any
other contaminants.
Wipe wall surfaces with a damp cloth and allow to dry.
Product names listed herein are trademarks of AS America Inc.
© AS America Inc. 2018
REQUIRED TOOLS AND MATERIALS
MATERIALS:
Suction Cups
Mineral Spirits
B) ROUGH PLUMBING & FITTINGS MUST BE INSTALLED
C) IF YOU PLAN TO INSTALL A SHOWER DOOR
INCLUDED MATERIALS:
x2 Tubes Adhesive
x1 Tube Color Matched Sealant
EACH ALCOVE STUD MUST
BE PLUMB AND SQUARE.
BEFORE WALLS
Turn off hot & cold water supplies.
Remove faucet handles, escutcheons, filler spouts and any
other fixtures & fittings (e.g. towel bars, soap dishes, etc.).
Use hammer & chisel to remove objects cemented to walls.
Old ceramic tiles, if solidly adhered to walls, need not be removed.
Loose ceramic tiles must be removed and sub walls sanded smooth.
Follow manufacturer's instructions and prepare stud wall accordingly.
75 5 58 8 -10 0 Rev. B 7 /18
Publicidad
Manuales relacionados para American Standard PASSAGE P2971SWT
Resumen de contenidos para American Standard PASSAGE P2971SWT
- Página 1 Visit http://www.americanstandard-us.com/passage-collection for coordinating products. Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
- Página 2 DRY FITTING THE TONGUE AND GROOVE PANELS ON THE WALL 1) Dry fit the panels starting with the rear most panels first. Keep a 1/8" (5mm) gap above the tub deck or shower base for all panels. When connecting several panels together, panels use a tongue and groove system to connect to each other. See Illustration 2.
- Página 3 3) With the aid of suction cups, move first rear panel onto the wall keeping a space of approximately 1/8" (5mm) off the surface of the tub deck or shower base. Press panel firmly over entire surface to ensure firm contact of panel to adhesive on wall. NOTE: It may be necessary to brace or support the panels against the wall until the panels stay securely in place.
- Página 4 AS America, Inc. (“American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this these walls or any of its parts that are found by American Standard, in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser.
- Página 5 Visite http://www.americanstandard-us.com/passage-collection para ver los productos que hacen juego. Gracias por elegir American Standard, el parámetro de excelente calidad por más de 100 años. Para asegurar que este producto se instale de manera adecuada, lea las instrucciones con atención antes de comenzar. (Para algunas instalaciones puede necesitarse ayuda profesional).
- Página 6 INSTALAR EN SECO LOS PANELES DE LA LENGÜETA Y LA RANURA EN LA PARED 1) Instale en seco los paneles. Comience con los paneles posteriores. Mantenga una brecha de 1/8" (5 mm) por encima de la superficie de la tina o la base de la ducha para todos los paneles. Para conectar varios paneles, se usa un sistema de lengüetas y ranuras.
- Página 7 3) Con la ayuda de ventosas, mueva el primer panel posterior hacia la pared. Mantenga un espacio de aproximadamente 1/8" (5 mm) de la superficie de la tina o la base de la ducha. Presione el panel firmemente sobre toda la superficie para asegurar un contacto firme del panel con el adhesivo en la pared.
- Página 8 1. Los defectos o daños que surjan del envío, la instalación, las modificaciones, los accidentes, el abuso, el uso incorrecto o la falta de mantenimiento y limpieza adecuados tal como se indica en el manual del propietario, así como el uso de refacciones que no sean American Standard auténticas, en todos los casos ya sea causado por un plomero contratista, una empresa de servicios, el propietario o cualquier otra persona.
- Página 9 Pour trouver des produits associés, visitez http://www.americanstandard-us.com/passage-collection Merci d'avoir choisi American Standard, la référence en matière de qualité depuis plus de 100 ans. Afin de garantir une installation adéquate, veuillez lire ces instructions attentivement avant de commencer. (Certaines installations peuvent requérir l’aide d’un professionnel.) De plus, assurez-vous que votre installation est en conformité...
- Página 10 INSTALLATION À SEC DES PANNEAUX À LANGUETTE ET RAINURE SUR LES MURS 1) Installer les panneaux à sec en commençant par le panneau le plus à l’arrière. Laisser un espace de 1/8 po (5 mm) au-dessus du tablier de la baignoire ou la base de la douche pour tous les panneaux. Lorsque vous reliez plusieurs panneaux, utiliser un système de rainure et languette pour les relier.
- Página 11 3) À l’aide des ventouses, déplacer le premier panneau arrière sur le mur en laissant un espace d’environ 1/8 po (5 mm) de la surface du tablier de la baignoire ou la base de la douche. Appuyer fermement sur le panneau et sur la surface complète pour assurer un contact ferme entre le panneau et l’adhésif sur le mur.
- Página 12 4. Les articles en option et les accessoires. La garantie limitée d’ A merican Standard sur ces articles est pour une durée d'un an sur les pièces seulement, et ne couvre pas la main-d'œuvre. Cette garantie limitée d'un an couvre les accessoires fabriqués par American Standard (p. ex., les tabliers, les drains, les barres d'appui, les systèmes de chauffage, et les garnitures) en ce qui a trait à...