YATO YT-82812 Manual Del Usuario página 18

GB
by pulling out the power cable.
Avoid accidental switching on of the chain saw. When you move the chain saw that is mains connected or which is connected to
its battery you must keep your fi ngers away from the power switch.
Always wear the correct, adjacent to the body, protective clothing.
Always operate the chain saw by holding it with both hands. While you are working you should secure loose pieces of wood, so
that they are prevent from moving, for example, by placing in them in a sawing jack. You should avoid cutting the wood, which is
located on the ground. You should avoid to process the wood, which is not secured against its movement during cutting.
During operation you should not hold the chain saw above your shoulders. You should not work with the chain saw, while you are
staying on the ladder. You should adopt such an position when you are working, that there would be no need to draw hands for
a full length.
Keep the chain clean. The chain must be sharpened and lubricated. This will ensure a more effi cient and safer work. The chain
can be sharpened in a specialized service. Before each use, check the condition of chain..
If you fi nd cracks, broken out teeth or any other damage, you should, before the start of the work, replace the chain with a new one.
In the case when you notice any damaged or broken parts of the chain saw, you should stop the work nor to start it. Damaged
parts must be replaced before the starting of work.
The chain saw must be used in accordance with the intended use, it is designed only for wood cutting. When you work, you must
be pay attention to metal or stone elements, which may be found in the processed wood.
Use only genuine spare parts. Usage of non-original spare parts may increase the risk of failure and lead to a body injury.
The chain saw should be repaired only in services, which has been authorized by the manufacturer. Use original spare parts. This
will minimize the risk of accidents and damage to equipment.
PRODUCT SERVICE
Preparing the chain saw for operation
Caution! Unplug the chainsaw from the power source before performing any installation and adjustment work. Remove both
batteries from the tool.
Mount the guide and cutting chain before fi rst use.
Remove the side panel locking bolt, then turn the tension knob until the panel can be detached from the chainsaw (II).
Mount the guide and chain as shown in the picture (III).
Make sure that the chain and guide are fi tted in the correct direction. The shape and direction of the links visible on the chainsaw
housing should correspond to the shape and direction of the chain. If there is a visible direction indication on the chain links, it
should have the same direction as the indication on the housing and guide.
Do not tension the chain yet, but make sure that the chain fi ts the guide slot and the teeth on the drive
wheel. Mount the side panel and tighten the locking knob. However, do it so as not to block the possibility of the guide movement.
Adjust the chain tension by turning the chain tension knob. Screw in the locking bolt. Check the chain tension. To do this, set the
chainsaw down and lift it by holding the middle part of the chain (IV). During
this test, the chain should lift above guide bar by 3 to 4 mm in the spot where it is held. If the chain is tensioned too
tight or too loose, loosen the locking knob a little and reset the chain tension. The chain tension should also be checked every 10
minutes of operation.
Check the technical condition of the chainsaw before connecting it to the power supply. If any damage is detected, it is forbidden
to connect it to the power supply before removing the damage.
Oil addition (VI)
Attention! Before all mounting and regulatory operations, you should disconnect the chain saw from the power supply. Chainsaw,
which are mains powered, should be disconnected from the wall outlet, the chain saw, which are battery operated, should be
disconnect from the battery.
For the lubrication of the chain and chain saw mechanisms you should only use the oil, which is intended for such purposes. For
the lubrication you should not use the worn out engine oil. It does not meet its task, which can cause damage to the mechanism
of chain saw.
Make sure, that lubricating oil is in its container. You should put the chain saw on a level surface, to check the oil indicator. The
oil level must not be less than an indication of the minimum quantity. If there is no such indicator, for reference, you should take
the bottom edge of the oil indicator.
It is forbidden to use the chain saw without the fi lled oil tank. This can cause damage to the chain, to guide and chain saw mech-
anisms. It is recommended that, start and chain saw operation be made, at least 3 meters from the place of oil supplementation.
Oil should be supplemented away from sources of fi re and heat.
In order to supplement the oil you should remove the oil tank cap, pour oil into the tank, so that the oil level aligns with a tag
indicating the maximum oil level or the upper edge of the oil level indicator, then fi rmly and tightly screw tank cap. If oil spills you
should carefully rub the remains of it before switching the chain saw to its supply.
O R I G I N A L I N S T R U C T I O N S
18