Milwaukee 6065-6 Manual Del Operador página 7

To reduce the risk of injury, the
WARNING
operator should be instructed in
the use, care and protection of grinding wheels
Grinding Wheel Selection
Use grinding wheels, and accessories that are:
• correct size as written on tool's nameplate.
• rated at or above the RPM listed on the tool's name-
plate.
• correct accessory, wheel type and grit for the job.
Grinding is the cutting action of thousands of abrasive
grains on the face of a grinding wheel. When grinding
metals such as steel and iron, choose an aluminum
oxide grinding wheel. Select a silicon carbide grinding
wheel for stone and concrete. Use cotton reinforced
wheels for non-ferrous metals.
Type 1 Reinforced 1/8" thick or less Cut-Off Wheels
are suited for small cut-off and shallow notching
operations only. Always handle wheels carefully to
avoid damage. Before installing any wheel, always
inspect it for cracks. If wheel is cracked, discard it to
prevent others from using it.
Care of Grinding & Cut-Off Wheels
Grinding/cut-off wheels should be protected from:
• wetness and extreme humidity
• any type of solvent
• extreme changes in temperature
• dropping and bumping
Grinding and cut-off wheels should be stored:
• in an organized way so wheels can be removed
without disturbing or damaging other wheels
• with their safety information
Grinding and cut-off wheels should NOT be dropped,
rolled or bumped.
Discard wheels that have been dropped, rolled,
bumped, subjected to extreme changes in tempera-
ture, or come into contact with solvents or wetness.
Only use accessories with Maxi-
WARNING
mum Safe Operating Speed rated
at least equal to the maximum speed marked on
the power tool. This speed is based on the
strength of the wheel, allowing for a reasonable
measure of safety. It is not meant to imply a best
or most efficient operating speed. Do not exceed
the Maximum Safe Operating Speed.
Installing/Removing Grinding Wheels
1. Unplug tool and place it upside down on a level
surface as shown. WARNING! Always unplug
tool before changing or removing accessories.
Remove any accessories from spindle.
2. Thread flange and nylon washer onto spindle.
Attach guard and grinding wheel as shown. (See
"Installing, Adjusting, and Removing the Guard"
for attaching guard). NOTE: When installing Type
27 or Type 29 grinding wheels, position disc nut
according to wheel thickness.
Position the guard in the location which offers best
control and guard protection. For operating zones
that provide maximum protection for the operator,
see "Grinding". NOTE: When selecting Type 11
grinding cup wheels, the guard's skirt should be
adjusted so that no more than 1/8" of the wheel
extends beyond the guard.
3. To tighten, press in the spindle lock button while
turning wheel or disc nut clockwise using the span-
ner wrench provided.
4. To remove grinding wheel and guard, unplug tool
and reverse procedure.
All manuals and user guides at all-guides.com
Type 27 or
Type 29
grinding
wheel
with flange
Hub adaptor
Screws
Lock
washers
Type 27
guard
Type 28
grinding
wheel
with hub
Type 28
guard
Removing and Replacing Quik-Lok
MILWAUKEE's exclusive Quik-Lok
instant field replacement or substitution.
1. To remove the Quik-Lok
2. To replace the Quik-Lok
7
1/8" thick
Disc nut
or less
wheels
Spindle
Screws
Lock washers
Spindle
(Select Models)
1/4 turn to the left and pull it out.
keyways and push the connector in as far as it will
go. Turn the cord nut 1/4 turn to the right to lock.
Disc nut position
1/4" thick
wheels
Type 27
or Type 29
grinding
wheel
with hub
Nylon
washer
Flange
Type 27
guard
Type 11
grinding
wheel
Nylon
washer
Flange
Type 11
guard
Cords
®
Cords provide
®
Cord, turn the cord nut
®
Cord, align the connector
®