Milwaukee 2702-20 Manual Del Operador página 5

Selecting Drill or Drive Action
(Cat. No. 2701-20)
1. To use the drilling mode, rotate
the torque selector collar until the
drill symbol appears in line
with the arrow.
2. To use the driving mode rotate
the torque selector collar until
the desired clutch setting ap-
pears in line with the arrow.
The adjustable clutch, when
properly adjusted, will slip at a
preset torque to prevent driving
the screw too deep into different
materials and to prevent damage
to the screw or tool.
Selecting Hammer, Drill or Drive Action
(Cat. No. 2702-20)
1. To use the hammer-drilling
mode, rotate the application
selector collar until the hammer
symbol appears in line with
the arrow. Apply pressure to the
bit to engage the hammering
mechanism.
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in hammer mode.
NOTE: When using carbide bits, do not use water
to settle dust. Do not attempt to drill through steel
reinforcing rods. This will damage the carbide bits.
2. To use the drilling only mode,
rotate the application selector
collar until the drill symbol
appears in line with the arrow.
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in
drilling mode.
3. To use the driving screws
mode rotate the application se-
lector collar until the drive symbol
appears in line with the ar-
row. Then rotate the torque se-
lector collar until the desired
clutch setting appears in line with
the arrow.
The adjustable clutch, when
properly adjusted, will slip at a preset torque to
prevent driving the screw too deep into different
materials and to prevent damage to the screw or
tool.
The torque specifications shown here are approximate
values obtained with a fully charged battery pack.
Cat. No. 2701-20
Clutch
Setting in. lbs
1-3 25-28 Small screws in softwood.
4-6 29-34
Medium screws in softwood or small
screws in hardwood.
7-9 36-39
Large screws in softwoods. Medium
10-13 40-44
screws in hardwood or large screws in
14-16 46-50
hardwood with pilot hole.
Applications
Cat. No. 2702-20
Clutch
Setting in. lbs
1-3 25-28 Small screws in softwood.
4-6 29-34
Medium screws in softwood or small
7-9 36-39
screws in hardwood.
10-13 40-44
Large screws in softwoods. Medium
14-17 46-51
screws in hardwood or large screws in
18 53
hardwood with pilot hole.
NOTE: Because the settings shown in the table are
only a guide, use a piece of scrap material to test the
different clutch settings before driving screws into
the workpiece.
Selecting Speed
The speed selector is on top of the motor housing.
Allow the tool to come to a complete stop before
changing speeds. See "Applications" for recom-
mended speeds under various conditions.
1. For Low speed, push the speed selector to display
"1".
2. For High speed, push the speed selector to display
"2".
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
Forward
Push to CENTER
For forward (clockwise) rotation, push in the control
switch from the right side of the tool. Check the
direction of rotation before use.
For reverse (counterclockwise) rotation, push in the
control switch from the left side of the tool. Check
direction of rotation before use.
To lock the trigger, push the control switch to the
center position. The trigger will not work while the
control switch is in the center locked position. Always
lock the trigger or remove the battery pack before
performing maintenance, changing accessories,
storing the tool and any time the tool is not in use.
5
Applications
Reverse
Lock -