Milwaukee 2607-20 Manual Del Operador página 48

EXAMPLE:
00
Component Parts (Small #)
0
Are Included When Ordering
The Assembly (Large #).
= Part number change from
«
previous service parts list.
FIG. PART NO. DESCRIPTION OF PART
1 06-82-5314 10-24 x 1/2" Pan Hd. Tapt. T-25 Screw (4)
2 44-10-0430 Depth Lever
3 45-08-0395 Depth Shaft
4 45-88-1515 Flat Washer
5 06-82-7470 6 x 11/16" Pan Hd. Plast. T-15 Screw
6 49-96-0080 3/16" Hex Key
7 12-20-1355 Service Nameplate Kit
8 31-44-1974 Right Handle Half
«
9 23-66-0221 Switch Assembly
«
10 --------------- Switch
11 42-42-1035 Switch Lock-Out
12 40-50-0350 Switch Lock-Out Spring
13 --------------- FET Module Assembly
14 --------------- Connector Block
15 40-50-1090 Compression Spring
16 34-40-4480 O-Ring
17 22-32-0420 Brush Spring Clip
18 22-20-0425 Brush Tube
19 22-18-1121 Brush Assembly - Red
20 22-18-1126 Brush Assembly - Black
21 40-50-8745 Brush Spring
22 31-44-1979 Left Handle Half
«
23 45-88-5615 Wave Spring Washer
24 02-04-5130 Ball Bearing
25 18-01-2000 Service Field
26 31-05-0350 Baffle
27 16-01-2111 Service Armature
28 14-74-0311 Shoe Assembly
29 34-60-0920 External Retaining Ring
30 02-04-1212 Ball Bearing
31 --------------- Gearcase
32 44-60-0740 Pivot Pin
33 06-82-7475 6 x 7/8" Pan Hd. Plast. T-15 Screw
34 06-75-5860 1/4-20 x 3/4" Hex Hd. Screw
35 --------------- Bushing
36 31-05-0053 Dust Port
«
38 06-82-5285 6-32 x 1/2" Pan Hd. Tapt. T-15 Screw
39 45-06-0720 Felt Seal
40 40-50-8040 Spindle Lock Spring
41 44-20-0651 Spindle Lock
42 42-42-1030 Spindle Lock Button
44 44-66-0565 Retaining Plate
SERVICE PARTS LIST
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
18 Volt Circular Saw
2630-20
CATALOG NO.
9 10 13
14
*
*
See page two
for service
note
28
56 57 58 59
60 61 62
NO. REQ.
(1)
(1)
(1)
(9)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(2)
(2)
(1)
(1)
(2)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(4)
(1)
(1)
(1)
(5)
(1)
(1)
(1)
(1)
(1)
STARTING
B57C
SERIAL
64 31
35
FIG. PART NO. DESCRIPTION OF PART
45 42-38-0222 Rubber Bumper
46 45-04-0485 10-32 x 13/16" Bumper Screw
47 28-41-0959 Lower Guard
48 40-50-0045 Guard Spring
49 06-82-0177 M5 x 0.8 Phillips PH Mach. Screw
«
50 34-60-0860 External Retaining Ring
51 43-34-0790 Inner Flange
52 28-20-1180 Upper Guard Cover
53 43-34-0795 Outer Flange
54 06-75-1010 Left Hand Blade Screw
55 14-46-2570 Spindle and Gear Assembly
56 43-98-0730 Bevel Adjustment Knob
57 45-88-1560 Washer
58 06-10-0660 1/4-20 x 1/2" Short Neck Carriage Bolt (1)
59 40-50-0650 Spring
60 43-98-0720 Rip Fence Knob
61 06-83-1600 10-32 x 3/8" Set Screw
62 06-82-9605 10-32 x 3/8" CSK Machine T-25 Screw (4)
63 --------------- 6-1/2" Blade
64 28-14-0748 Gearcase Assembly w/ Bushing
10-15-0500 Warning Label (Not Shown)
49-22-1001 Rip Fence (Not Shown)
48-55-3500 Contractors Bag (Not Shown)
FIG. NOTE:
30 Orient the Ball Bearing so that the seal faces the fan and
the open side faces the Gearcase.
35 Press Needle Bearing flush to .015 sub-flush in Gearcase.
41 Functionally check Spindle Lock. Spindle Lock must return
briskly when released from engagement in gear.
50 Position Retaining Ring with rounded edge facing
Lower Guard.
10,11 Functionally check Switch Lock-Out by attempting to turn
on tool by applying a reasonable amount of force, up to 8 lbs.,
to the switch trigger. The tool must not turn on. Release
trigger. Actuate the lock-out lever and apply a reasonable
amount of force to the switch trigger. The tool must turn on.
While the trigger is still in the "ON" position, release the
lock-out. Release the trigger. The tool must stop and the
lock-out lever must again prevent the actuation of the Switch.
Repeat the switch check two more times.
FIG. LUBRICATION:
31 Apply 3.0 grams of "Y" grease, No. 49-08-5270 to gear bore
of Gearcase. The grease should be directed toward the
pinion end of the armature.
Apply a light film of lubricant to the bearing bore of the
Gearcase before assembling the armature/bearing.
MILWAUKEE TOOL
13135 W. Lisbon Rd., Brookfield, WI 53005
BULLETIN NO.
54-40-2632
DATE
REVISED BULLETIN
54-40-2631 May 2020
WIRING INSTRUCTION
SEE REVERSE SIDE
NOTE: Functionally
check Lower Guard #47,
with saw set at full depth of
cut and 0° bevel. Place saw
upside down with Shoe horizontal.
Fully retract Guard and then release it.
The Guard must return briskly.
NO. REQ.
www.milwaukeetool.com
l
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
Drwg. 1