Descargar Imprimir esta página

Milwaukee 2607-20 Manual Del Operador página 75

Ocultar thumbs Ver también para 2607-20:

Publicidad

Idiomas disponibles

Idiomas disponibles

Using Cut-Off Wheels
Cut-Off Wheels are suited for small cut-off and shal-
low notching operations only.
The guard type must match the
WARNING
wheel type to provide maximum
protection for the operator if the wheel should
break.
When using a cut-off wheel, hold the tool as shown,
using only the edge of the wheel. WARNING! Using
the face of a Cut-Off Wheel (as in grinding) will cause
the Wheel to crack and break, resulting in serious
personal injury.
Using Wire Brushes
Wire brushes are useful for removing rust, scale,
burrs, weld slag, etc.
Everyone in the area must wear
WARNING
protective clothing and safety
goggles or face shields. Fatigued wires and
residue will fly off the brush with considerable
force, causing potential for serious injury.
Never exceed Maximum Safe Operating Speed of
brush. Do not use a damaged brush or one that
is functioning improperly (throwing wires, out-
of-balance, etc.). These conditions increase the
possibility of further brush failure and possible
injury. Discard and replace damaged brushes
immediately.
A Type "27" guard must be installed when using
a wire wheel brush to provide maximum protec-
tion for the operator when fatigued wires break.
(See "Removing/Installing/Adjusting the guard".)
Always install wire brushes according to the acces-
sory manufacturer's instructions. Only use acces-
sories with threads matching the tool spindle.
Guard
Test wheel for balance and loose or damaged wires
by letting it spin for one minute before applying it to
the workpiece. During this time, no one should stand
in front of or in line with it.
Control pressure and surface contact between
wheel and workpiece. Too much pressure causes
over-bending of wires and heat build-up causing
premature wire breaking, rapid dulling and reduced
brush life. Instead of more pressure, try a wire wheel
with more aggressive cutting action (increased wire
size, decreased wire length or different brush type
(knot type vs. crimped wire type).
Hold tool at 5° to 15° angle to ensure proper sanding
pressure and control. Too great an angle will result
in too much pressure and could cause excessive
wear to the disc and workpiece. Too small an angle
will reduce control.
Use long, sweeping, side to side strokes, advancing
forward to produce the desired finish.
Cross Sanding - When finishing a surface that
has been prepared by a coarse disc or wheel, sand
at right angles to the strokes made by the coarser
disc. Finishing marks left from previous sanding are
easily seen and removed for a uniform finish. Failure
to cross sand when changing from a coarse disc to
a finishing disc may result in deep scratches and
circular marks.
Removing Welds or Hammer Marks - When remov-
ing welds or hammer marks, limit coarse sanding to
the immediate area. Use successively finer grits to
smooth surface.
Finishing Metal - Constantly move across the sur-
face. Work faster on curved surfaces where contact
areas are smaller and pressure is greater. Flat areas
may appear at the end of the stroke when pressure
Wire Wheel
is too heavy. Ease up on pressure at end of each
Brush
stroke and when reversing strokes.
Deep scratches and circular marks can result from:
• Using too coarse a grit
• Using a partially glazed disc
• Dirt or loose metal on the workpiece
• Failure to sand across the grain when changing from
coarse to finishing discs
Wire Cup
• Failure to use closed coated discs to reduce the
Brush
problem of grains working loose and scratching the
workpiece
Bluish discoloration of metal surface indicates:
• Excessive heat caused by circular motion in a small area
• Excessive pressure
• Use of worn out or glazed discs
8
Using Sanding Discs
For best result use only this portion of disc
Troubleshooting
Hold at a
Hold at a
5° to 15°
5° to 15°
angle
angle

Publicidad

loading

Este manual también es adecuado para:

2606-20