Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

CJD3 SERIES
RANGE HOOD
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer at the address or telephone number
listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel and
lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a prominent warning device, such as a tag, to
the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards, includ-
ing fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent backdraft-
ing. Follow the heating equipment manufacturer's guideline and safety
standards such as those published by the National Fire Protection As-
sociation (NFPA), and the American Society of Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
6. To reduce the risk of fire or electric shock, do not use this range hood
with an additional speed control device.
7. Ducted fans must always be vented to the outdoors.
8. To reduce the risk of fire, use only metal ductwork.
9. Use with approved cord-connection kit only.
10. This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers cause
smoking and greasy spillovers that may ignite. Heat oils slowly on low or
medium settings.
2. Always turn hood ON when cooking at high heat or when cooking flaming
foods.
3. Clean ventilating fans frequently. Grease should not be allowed to
accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the size of
the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray,
then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the
flames do not go out immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - violent steam
explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you already know
how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on "Kitchen Fire Safety Tips" published by NFPA.
!
FOR DOMESTIC COOKING ONLY
!
CAUTION
1. For indoor use only.
2. For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
3. To avoid motor bearing damage and noisy and/or unbalanced impellers,
keep drywall spray, construction dust, etc. off power unit.
4. A maximum height of 30" from the top of the hood to the cooktop is rec-
ommended for best capture of cooking impurities. The top of the hood
MUST NOT BE LESS than 24" above the cooktop.
5. Please read specification label on product for further information and
requirements.
Installer: Leave this manual with
the homeowner.
Homeowner: Operating and
Cleaning information on page 6.
NOTE
If hood is to be installed Non-Ducted:
Purchase a set of (2) non-ducted filters from your
local distributor or retailer and attach them to the
aluminum mesh filters.
TABLE OF CONTENTS
This manual is divided into sections as follows:
"PREPARE HOOD LOCATION"
Run ductwork from roof or wall cap, and electrical wiring from service
panel - to installation location
"PREPARE THE HOOD"
Get your hood ready for installation
"CONNECT WIRING"
Make electrical wiring connections to hood
"INSTALL HOOD"
Secure hood to cabinet and ductwork - install bulbs and filters
"OPERATION"
How to use the hood controls
"CLEANING"
Keep your hood in top working condition
"SERVICE PARTS"
Part numbers and exploded view of hood components
"WARRANTY"
One-year limited warranty and how to contact us
Register your product online at: www.broan.com/register
CJD3 SERIES
Page 1
Patent No.:
US D450, 829 S
!

Publicidad

loading

Resumen de contenidos para Broan CJD3 Serie

  • Página 1 B. The fire is small and contained in the area where it started. C. The fire department is being called. D. You can fight the fire with your back to an exit. * Based on “Kitchen Fire Safety Tips” published by NFPA. Register your product online at: www.broan.com/register...
  • Página 2 CJD3 SERIES Page 2 PREPARE HOOD LOCATION PREPARE HOOD LOCATION 7” ROUND ROOF CAP 3¼" X 10" or 7" ROUND DUCT VERTICAL DUCTING (For vertical discharge) SOFFIT HOUSE WIRING (Top or Back of hood) CABINET WALL CAP HOOD HOOD 24" - 30" ABOVE 3¼"...
  • Página 3 CJD3 SERIES Page 3 PREPARE THE HOOD PREPARE THE HOOD AIR CHUTE Remove Air Remove Chute - held in Teflon -coated ® place with one bottom cover (1) screw. from hood. Set cover and mounting screws NOTE: Be aside. careful not to disconnect any Teflon ®...
  • Página 4 CJD3 SERIES Page 4 PREPARE THE HOOD PREPARE THE HOOD UP TO 1” TAPE TOP RECTANGULAR SIDE-TO-SIDE ADJUSTMENT DUCT KNOCKOUT DAMPER/ SEMI-CIRCULAR (Remove for 3¼” x 10” DUCT DUCT KNOCKOUT Vertical & for 7” Round CONNECTOR (Remove for 7” Round Discharge) (Vertical Discharge)
  • Página 5 CJD3 SERIES Page 5 CONNECT THE WIRING INSTALL THE HOOD WARNING: To reduce the risk of electric shock, make sure power is switched off at the service panel. Lock or tag service panel to prevent power from being switched on accidentally. HOUSE WIRING MOUNTING SCREW (4)
  • Página 6 CJD3 SERIES Page 6 NON-DUCTED FILTERS HEAT SENTRY The heat sentry continuously monitors temperature and will automatically turn the fan on to high speed when the temperature If hood is to be installed Non-Ducted: is above normal. Purchase a set of (2) Non-Ducted Filters from your local The fan button will flash while the heat sentry is active.
  • Página 7 NON DUCTED FILTER KIT, 36 IN Order replacement parts by PART NO. - not by KEY NO. * Standard hardware - may be purchased locally. ** Not illustrated - purchase separately. Replacement parts can now be ordered on our website. Please visit us at www.Broan.com...
  • Página 8 Limited Warranty Warranty Period and Exclusions: Broan-NuTone LLC (the “Company”) warrants to the original consumer purchaser of its product (“you”) that the product (the “Product”) will be free from material defects in the Product or its workmanship for a period of one (1) year from the date of original purchase.
  • Página 9 Garantía limitada de un año y cómo comunicarse con nosotros D. Usted puede combatir el incendio con una salida a su espalda. Registre su producto en línea en: www.broan.com/register * Basado en las recomendaciones para “Seguridad en la Cocina” publicadas...
  • Página 10 SERIE CJD3 Página 10 PREPARACIÓN DEL LUGAR DONDE PREPARACIÓN DEL LUGAR DONDE SE VA A INSTALAR LA CAMPANA SE VA A INSTALAR LA CAMPANA TAPA DE TECHO CONDUCTO DE SISTEMA VERTICAL DE CONDUCTOS 8,3 cm x 25,4 cm O REDONDOS DE 17.8 CM (7”) REDONDO DE 17,8 cm 35,4 cm 35,4 cm...
  • Página 11 SERIE CJD3 Página 11 PREPARACIÓN DE LA CAMPANA PREPARACIÓN DE LA CAMPANA Quite la Cubi- CONDUCTO erta inferior PARA AIRE Quite el con- recubierta de ducto para aire Teflón ® - fijado con un la campana. (1) tornillo. Coloque a un lado la cubierta y los NOTA: Tenga...
  • Página 12 SERIE CJD3 Página 12 PREPARACIÓN DE LA CAMPANA PREPARACIÓN DE LA CAMPANA AJUSTE LATERAL CINTA AGUJERO CIEGO SUPERIOR DEL HASTA DE 2.5 CM (1”) CONECTOR CONDUCTO RECTANGULAR AGUJERO CIEGO (Quite en el caso de descargas verti- PARA CONDUCTO SEMI- REGULADOR cales de 8.3 cm x 25.4 cm CIRCULAR DE TIRO/...
  • Página 13 SERIE CJD3 Página 13 CONEXIÓN ELÉCTRICA INSTALACIÓN DE LA CAMPANA ADVERTENCIA: Para reducir el riesgo de descar- gas eléctricas, asegúrese de apagar el interruptor de alimentación eléctrica en el panel de servicio. Bloquee o rotule el panel de servicio para evitar que alguien conecte accidentalmente la energía eléctrica.
  • Página 14 SERIE CJD3 Página 14 FILTROS SIN CONDUCTOS CONTROLADOR DE CALOR El controlador de calor continuamente monitorea la temperatura y automáticamente enciende el ventilador a alta velocidad cuando la Si la campana se va a instalar en un sistema sin conductos: temperatura está...
  • Página 15 Ordene partes de reemplazo por número de Parte - no por número de Clave. se pueden ahora pedir en nuestro Web site. * Piezas Estándar - pueden ser compradas localmente. ** No se muestra - cómprese por separado. Visítenos por favor en www.Broan.com...
  • Página 16 Garantía limitada Periodo y exclusiones de la garantía: Broan-NuTone LLC (la “Compañía”) garantiza al consumidor comprador original de su producto (“usted”) que el producto (el “Producto”) estará libre de defectos en materiales o en mano de obra, por un periodo de un (1) año a partir de la fecha de compra original.