Nolan N40-5GT Seguridad E Instrucciones página 11

N40-5GT
WARNING
- The presence of dust between the two visors may produce scratches on both
surfaces.
- Scratched PINLOCK visors and inner visors may cause reduced visibility and
®
must therefore be replaced.
- Regularly check the correct stretch of the PINLOCK
from moving and scratching both surfaces.
- If the helmet visor fogs up and/or condensation forms between the visors, check
that the PINLOCK inner visor is both correctly assembled and stretched.
®
- An excessive and early stretch of the PINLOCK
adherence against the visor surface and/or permanent deformations with subse-
quent inability to correctly perform any following adjustments.
- Intense sweating /breathing, the use under particular weather conditions (low tem-
peratures, and/or high humidity and/or sudden changes in temperature and/or
heavy rain) and/or intense and prolonged use may affect the performance of the
PINLOCK ® inner visor and cause fogging or formation of condensation. In such
cases, after using the helmet and to restore the system efficiency, remove the
PINLOCK ® inner visor from the helmet visor and let it dry with dry and warm air.
The same procedure must be applied to the helmet, in order to dry out humidity in
case it has formed up as a consequence of the conditions described above.
10. INNER VISOR PINLOCK DISASSEMBLY
®
10.1. Remove the visor equipped with the Pinlock
above).
10.2. Widen the visor and release the Pinlock
10.3. Release the visor.
MAINTENANCE AND CLEANING
- Remove the PINLOCK ® inner visor from the visor. Using a damp and soft cloth,
gently clean it with neutral liquid soap. Remove the soap under running water.
- Dry the inner visor with dry and warm air without wiping it.
- To keep the features of the inner visor in good conditions over time, let the helmet
dry in a ventilated and dry place with the visor open after use. Keep it away from
heat sources and store it in a place away from direct light.
- Do not use solvents or chemical products.
SIDE PLATES
When the helmet N40 GT is configured without the visor the side plates must be as-
5
sembled in its place.
11. SIDE PLATES ASSEMBLY
To assemble the side plates first remove the lateral latches and (if assembled) the peak
and the visor (see instructions above).
11.1. Place the left side plate on the corresponding side mechanism centring its hole
on the mechanism and its teeth (Fig. 16).
11.2. If you wish to assemble the peak above the plates see the relevant installation
instructions.
20
INSTRUCTIONS FOR USE
inner visor to prevent the it
®
inner visor may result in excessive
®
inner visor (see instructions
®
inner visor from the pins (Fig. 13).
®
11.3. Assemble the left lateral latch as indicated in the instructions above.
11.4. Follow the same steps on the right side of the helmet.
12. SIDE PLATES DISASSEMBLY
To disassemble the side plates first remove the lateral latches and (if assembled) the
peak (see instructions above).
Then remove the plates from the side mechanisms.
Next, reassemble the visor and then the peak (if any) as explained in the previous
instructions.
WARNING
- When using the helmet in a configuration without the visor, always assemble the
lateral latches and the side plates.
- Do not use the helmet if the plates and the lateral latches have not been assem-
bled properly.
- If the peak is assembled over the plates the proper operation as described previ-
ously.
- Do not remove the side mechanisms from the shell.
- Should any of the side mechanisms fail or be damaged, please refer to a Nolan-
group authorized dealer.
VISION PROTECTION SYSTEM ( VPS ) ( VPS - 11S )
The exclusive inner VISION PROTECTION SYSTEM (VPS) is a LEXAN™ (*) polycar-
bonate moulded sunscreen with scratch-resistant/fog-resistant treatment. Very simple
and practical to use. Just lower to activate it or lift to remove it from the field of vision.
It is useful in all sorts of situations, both on long journeys out of town and shorter town
trips.
Moreover, the innovative fastening system allows you to assemble and disassemble
the sunscreen without the need for any tools for ordinary maintenance and cleaning
operations.
VPS OPERATION
The VPS mechanism allows to activate the sunscreen by simply lowering it until it par-
tially covers the visor field of vision. In this way, the desired light transmittance reduc-
tion is achieved. At any time, without operating the visor, the VPS can be deactivated
with a simple movement and easily lifted up to restore the normal conditions of visibility
and protection guaranteed by the approved helmet visor.
To deactivate the VPS, push the side slider completely downwards (Fig. 17A).
To completely activate the VPS push the side slider completely upwards (Fig. 17B).
The VPS is adjustable in a range of intermediate positions to ensure the best comfort
for the user with respect to the terms of use.
PRECAUTIONS FOR USE
Current homologation standards (ECE22-06) establish that the minimum light trans-
mittance levels of visors must be no less than 80%; for homologated sunscreens, the
minimum transmittance level must be no less than 20%.
(*) LEXAN is a trademark of SABIC.
N40-5GT
21
INSTRUCTIONS FOR USE