Nilfisk SM 800 Manual De Uso página 5

INTRODUCTION
NOTE: The numbers in brackets refer to the components shown in
Machine Description chapter.
Before operating the machine, read carefully this manual.
OTHER REFERENCE MANUALS
Spare Parts List (supplied with this manual).
SPARE PARTS AND MAINTENANCE
Any repair must be performed at authorised Nilfisk Service Centers by
qualified personnel, which will use original spare parts and accessories.
For more information, please consult the website: www.nilfisk.com.
UNPACKING/DELIVERY
Upon delivery check that the packing and the machine were not damaged
during transportation. In case of visible damages, keep the whole packing
to have it checked. Contact your Nilfisk Dealer immediately to file a freight
damage claim.
Remove the sweeper from the packing, loosen the knobs (2) and unfold
the handlebar (1). Tighten the knobs to fasten the handlebar.
GENERAL INSTRUCTIONS
Specific warnings and cautions to inform about potential damages to
people and machine are shown below.
WARNING!
To reduce the risk of fire or personal injuries:
– This sweeper is not suitable for collecting dangerous powders.
– Do not collect toxic, carcinogen, combustible materials or
other dangerous materials such as asbestos, arsenic, barium,
beryllium, lead, pesticide or other harmful materials.
– Do not collect burning cigarette butts or other burning objects,
ash, matches or similar.
– To remove glass, metals or sharp objects from the collection
tank, wear thick gloves to prevent personal injuries.
– Empty the collection tank after each use.
– This walk-behind sweeper is not suitable to collect liquids.
– This sweeper must be used in dry conditions, it must not be used
or kept outdoors in wet conditions.
– Do not use the sweeper on inclined surfaces.
–
Do not allow to be used as a toy. Pay careful attention when
using the machine near children.
– Use only brooms supplied with the machine or those specified in
the User Manual. Using other brooms could reduce safety.
– Before using the sweeper, the collection tank must be as shown
in the User Manual.
– During the sweeper operation, foreign materials may get into
the eyes of the operator. Thus, it is advisable to wear protective
glasses.
– Please be watchful. Pay careful attention to the machine
operation and use common sense. Do not use the machine when
tired, absent-minded, under the effect of drugs, alcoholics or
medicines which can compromise the control over the machine.
USER MANUAL
MACHINE DESCRIPTION
(See figure on Page 2)
1. Adjustable handlebar
2. Handlebar adjusting knobs
3. Collection tank
4. Collection tank handle
5. Side broom height adjusting knob
6. Side broom
7. Main broom height adjusting knob
8. Fixed front main broom
9. Adjustable rear main broom
10. Rear wheel
11. Front pivoting wheel
12. Sweeper frame
13. Main broom rotation direction
14. Side broom rotation direction
SWEEPER OPERATION
1. If necessary, adjust the handlebar (1) to one of the 3 positions, by
using the knobs (2).
2. Grab the handlebar and push the machine forward no faster than
a normal walking pace. The machine does not work if dragged
backwards.
3. The collection tank (3) should be emptied after each working cycle
and whenever it is full.
AFTER USING THE MACHINE
After working, before leaving the machine: empty the collection tank (4)
and check the main brooms (8 and 9) to remove foreign materials (lace,
wire, strings or similar) which can compromise the proper operation.
To store the machine in a narrow place, fold the handlebar (1).
– Loosen the knobs (2) and pull the handlebar upwards.
– Fold down the handlebar and lock it.
Then place the machine in a vertical position to preserve the broom
bristles.
BROOM ADJUSTMENT
Adjust the broom height when the bristles are worn or when their
efficiency is compromised.
1. Adjust the height of the main broom (9) with the two knobs (7). When
turning them, each step on the marked numbers amounts to a broom
lowering.
Check that the two knobs (7) are on the same marked number.
Otherwise there will be a difference in the longitudinal pressure of
the broom.
2. Adjust the height of the side brooms (6) with the knobs (5). When
turning them counter-clockwise, each step amounts to a broom
lowering.
After the adjustment, push the machine to check that it moves smoothly,
without difficulty or resistance. Otherwise, repeat the broom adjustment
procedure.
If the brooms are too worn, replace them.
For more information, please consult the Manual on the website:
www.nilfisk.com.
SCRAPPING
Have the machine scrapped by a qualified scrapper.
SM 800 1464441000(3)2010-04
ENGLISH
5