Sony MEX-BT5000 Manual De Instrucciones página 27

CD/MD playback
The disc cannot be loaded.
• Another disc is already loaded.
• The disc has been forcibly inserted upside down or in
the wrong way.
The disc does not playback.
• Defective or dirty disc.
• The CD-Rs/CD-RWs are not for audio use (page 22).
MP3/WMA files cannot be played back.
The disc is incompatible with the MP3/WMA format
and version (page 22).
MP3/WMA files take longer to play back than
others.
The following discs take a longer time to start
playback.
– a disc recorded with a complicated tree structure.
– a disc recorded in Multi Session.
– a disc to which data can be added.
The ATRAC CD cannot play.
• The disc is not created by authorized software, such
as SonicStage or SonicStage Simple Burner.
• Tracks that are not included in the group cannot be
played.
The display items do not scroll.
• For discs with very many characters, those may not
scroll.
• "Auto Scroll" is set to "off."
t Set "Auto Scroll on" (page 19) or press (SCRL).
The sound skips.
• Installation is not correct.
t Install the unit at an angle of less than 45° in a
sturdy part of the car.
• Defective or dirty disc.
The operation buttons do not function.
The disc will not eject.
Press the RESET button (page 6).
Radio reception
The stations cannot be received.
The sound is hampered by noises.
• Connect a power aerial control lead (blue) or
accessory power supply lead (red) to the power
supply lead of a car's aerial booster (only when your
car has built-in FM/AM aerial in the rear/side glass).
• Check the connection of the car aerial.
• The auto aerial will not go up.
t Check the connection of the power aerial control
lead.
• Check the frequency.
• When the DSO mode is on, the sound is sometimes
hampered by noises.
t Set the DSO mode to "off" (page 19).
Preset tuning is not possible.
• Store the correct frequency in the memory.
• The broadcast signal is too weak.
Automatic tuning is not possible.
• The local seek mode is set to "on."
t Set to "Local off" (page 19).
• The broadcast signal is too weak.
t Perform manual tuning.
During FM reception, the "ST" indication
flashes.
• Tune in the frequency accurately.
• The broadcast signal is too weak.
t Set to "Mono on" (page 19).
An FM programme broadcast in stereo is heard
in monaural.
The unit is in monaural reception mode.
t Set to "Mono off" (page 19).
Bluetooth function
The connecting device cannot detect this unit.
• Set "Signal" to "ON" (page 14).
• Set "Visibility" to "Show" (page 14).
• While connecting to the other Bluetooth device, this
unit cannot be detected from another device.
Disconnect the current connection and search for this
unit from another device. The disconnected device
can be reconnected by selecting from the list of
registered devices.
This unit cannot detect the connecting device.
Check the Bluetooth setting of the connecting device.
Connection is not possible.
• Depending on the other device, searching from this
unit may not be possible.
t Search for this unit from the other device.
• Depending on the status of the other device,
searching from this unit may not be possible.
t Search for this unit from the other device.
• Check the pairing and connection procedures in the
manual of the other device, etc., and perform the
operation again.
The name of the detected device does not
appear.
Depending on the status of the other device, it may not
be possible to obtain the name.
No ring tone.
• Adjust the volume in "Ring Vol" (page 16).
• Depending on the connecting device, the ring tone
may not be sent properly.
t Set "Ringtone" to "Default" (page 17).
The talker's voice volume is low.
Adjust the volume in "Talk Vol" (page 16).
Echo or noise occurs in phone call
conversations.
• Lower the volume.
• "EC/NC Mode" is set to "off."
t Set "EC/NC Mode" to "Mode 1" or "Mode 2"
(page 18).
• If the ambient noise other than the phone call sound
is loud, try reducing this noise.
E.g.: If a window is open and road noise, etc., is loud,
shut the window. If the air conditioner is loud, lower
the air conditioner.
continue to next page t
27