Publicidad
Idiomas disponibles
Idiomas disponibles
Installing Backing Pad and Sanding Discs
1. Unplug the tool. WARNING! Always unplug tool
before changing or removing accessories.
2. Wipe the accessories, disc nut and spindle to
remove dust and debris. Inspect the parts for dam-
age. Replace if needed. Use only MILWAUKEE
mounting hardware designed for your tool.
3. Slip backing pad onto spindle with flat side away
from gear case.
4. Place sanding disc on backing pad and secure
assembly to spindle with disc nut.
Disc nut
Sanding
disc
Backing
pad
Spindle
5. Press in the spindle lock button while turning disc
nut clockwise. Tighten securely.
6. To remove backing pad and sanding disc, unplug
the tool and reverse the procedure.
OPERATION
To reduce the risk of injury, always
WARNING
wear safety goggles or glasses
with side shields. Never grind without proper
safety equipment.
Always hold the tool firmly with both hands using
the handles provided before and during grinding.
Paddle Switch Operation
To start the tool, grasp the handle and side handle
firmly. Pull the lock-off button back and squeeze the
paddle switch.
To stop the tool, release the paddle switch. Make
sure the tool comes to a complete stop before laying
the tool down.
To lock-on the switch, start the tool and push in the
lock-on button. To stop the tool, squeeze and release
the paddle switch. Make sure the tool comes to a
complete stop before laying the tool down.
General Operation
1. If you have just installed an accessory or are
beginning a period of work, test the wheel by
letting it spin for one minute before applying it to
the workpiece. WARNING! Never use a grinding
wheel that has been dropped. Out-of-balance or
damaged accessories can mar workpiece, dam-
age the tool, and cause stress that may cause
accessory failure.
2. Use a clamp, vise or other practical means to hold
your work, freeing both hands to control the tool.
3. WARNING! Hold tool securely with both hands.
Start the tool.
4. Allow accessory to come to full speed before
beginning work.
5. Control pressure and surface contact between
accessory and workpiece. WARNING! Never
bang grinding wheel onto work.Too much pressure
causes accessory failure or slows speed.
6. When finished, turn off the tool and make sure it
comes to a complete stop before laying it down.
Using Grinding Wheels
The guard type must match the
WARNING
wheel type to provide maximum
protection for the operator if the wheel should
break.
When grinding, hold tool at a 5
constant pressure for a uniform finish. Too great an
angle causes concentrated pressure on small areas
which may gouge or burn work surface.
For best result use only this portion of disc
Using Cut-Off Wheels
Cut-Off Wheels are suited for small cut-off and shal-
low notching operations only.
The guard type must match the
WARNING
wheel type to provide maximum
protection for the operator if the wheel should
break.
When using a cut-off wheel, hold the tool as shown,
using only the edge of the wheel. WARNING! Using
the face of a Cut-Off Wheel (as in grinding) will cause
the Wheel to crack and break, resulting in serious
personal injury.
Using Wire Brushes
Wire brushes are useful for removing rust, scale,
burrs, weld slag, etc.
Everyone in the area must wear
WARNING
protective clothing and safety
goggles or face shields. Fatigued wires and
residue will fly off the brush with considerable
force, causing potential for serious injury.
Never exceed Maximum Safe Operating Speed of
brush. Do not use a damaged brush or one that
is functioning improperly (throwing wires, out-
of-balance, etc.). These conditions increase the
possibility of further brush failure and possible
injury. Discard and replace damaged brushes
immediately.
A Type "27" guard must be properly installed
when using a wire wheel brush to provide maxi-
mum protection for the operator when fatigued
wires break. (See "Removing/Installing/Adjusting
the guard".)
Always install wire brushes according to the acces-
sory manufacturer's instructions. Only use acces-
sories with threads matching the tool spindle.
7
to 15
angle, using
o
o
Hold at a
5° to 15° angle
Publicidad
