Publicidad
Idiomas disponibles
Idiomas disponibles
14 | English
(16) Vacuum hose (dia. 35 mm)
a)
(17) Dust/chip bag
a)
(18) Parallel guide
a)
(19) Scale for rebate width
(20) Locking nut for rebate width setting
(21) Fastening screw for parallel/angle guide
a)
(22) Angle guide
Technical Data
Planer
Article number
Rated power input
Power output
No-load speed
Cutting depth
Rebate depth
Max. planing depth
Weight according to EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Noise/vibration information
Noise emission values determined according to
EN 62841‑2‑14.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 86 dB(A); sound power level
97 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 62841‑2‑14:
2
2
a
= 4,5 m/s
, K = 1,5 m/s
.
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
1 609 92A 83S | (08.07.2022)
a)
(23) Locking nut for angle setting
(24) Fastening screw for rebate depth guide
(25) Rebate depth guide
(26) Parking rest
a)
a) Accessories shown or described are not included with the
a)
Fitting
u
Changing the tool
u
Use only original Bosch HM/TC planer blades. The hard
metal (HM/TC) planer blade has two cutting edges and can
be turned. If both cutting edges become blunt, the planer
blade (14) needs to be changed. The HM/TC planer blade
must not be resharpened.
Removing the planer blade (see figure A)
To turn or replace the planer blade (14), turn the blade head
(11) until it is parallel to the planer base plate (9).
➊ Loosen the two fastening screws (13) using the hex key
(15) (approx. 1–2 turns).
➋ If necessary, loosen the clamping element (12) by lightly
striking it with an appropriate implement, e.g. a wooden
wedge.
➌ Use a piece of wood to push the planer blade (14) to the
side and out of the blade head (11).
Fitting the planer blade (see figure B)
The guide groove on the planer blade ensures a constant,
even height setting when changing or turning the blade.
If necessary, clean the knife seat in the clamping element
(12) and the planer blade (14). When fitting the planer
blade, ensure that it is securely seated in the mounting guide
of the clamping element (12) and is aligned flush with the
a)
product as standard. You can find the complete selection of
accessories in our accessories range.
PHO 1500
3 603 BA4 0..
W
550
W
280
-1
min
19 500
mm
0–1.5
mm
0–8
mm
82
kg
2.4
/II
Pull the plug out of the socket before carrying out any
work on the power tool.
Take care when changing the planer blade. Do not pick
up the planer blade by the cutting edges. You may be
injured by the sharp cutting edges.
a)
a)
PHO 2000
3 603 BA4 1..
680
400
19 500
0–2.0
0–8
82
2.4
/II
Bosch Power Tools
Publicidad
