Bosch PHO Professional 1500 Manual Original página 16

16 | English
Excessive feed reduces the quality of the surface finish and
can lead to the chip ejector quickly becoming blocked.
Only sharp planer blades achieve good cutting performance
and make the power tool last longer.
The integrated parking rest (26) also enables a continuation
of the planing procedure following interruption at any point
on the workpiece:
– Place the power tool – with parking rest folded down –
onto the area of the workpiece that you will continue to
work on.
– Switch the power tool on.
– Shift the contact pressure onto the front of the planer
base plate and slowly slide the power tool forward (➊). In
doing so, the parking rest will swivel upwards and out of
the way (➋), meaning that the rear section of the planer
base plate is in contact with the workpiece again.
– Guide the power tool over the surface of the workpiece,
applying uniform feed (➌).
Chamfering edges (see figure H)
The V-grooves in the front of the planer base plate enable
quick and easy chamfering of workpiece edges. Select the V-
groove that corresponds to your chamfering width. Then po-
sition the planer with the V-groove onto the edge of the
workpiece and guide it along.
Groove used
None
Small
Medium
Large
Planing with the Parallel/Angle Guide (see figures D–F)
Attach the parallel guide (18) or the angle guide (22) to the
power tool with the fastening screw (21). Depending on the
application, attach the rebate depth guide (25) to the power
tool with the fastening screw (24).
Loosen the locking nut (20) and set the desired rebate width
on the scale (19). Retighten the locking nut (20).
Set the desired rebate depth accordingly using the rebate
depth guide (25).
Carry out the planing procedure several times until the de-
sired rebate depth has been achieved. Guide the planer with
sideways contact pressure.
Chamfering with angle guide
Use the angle setting (23) to
set the necessary helix angle
when chamfering grooves
and surfaces.
Storage compartment
In the storage compartment (7), you can store a planer
blade (14) (only on PHO 2000) and a hex key (15) as shown
1 609 92A 83S | (08.07.2022)
in the illustration. To remove the compartment contents, pull
the storage compartment (7) completely out of the planer.
(14)
Maintenance and Service
Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
Dimension a
after-sales service centre that is authorised to repair Bosch
(mm)
power tools.
0–2,5
Keep the parking rest (26) clear and clean it regularly.
1,0–4,5
After-Sales Service and Application Service
2,0–5,0
2,5–6,0 Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
(15)
(7)
(25)
Bosch Power Tools