EINHELL GE-WS 18/75 Li Manual De Instrucciones página 13

6. Operation
6.1 Switching on
After inserting the battery, switch the equipment
on by turning the On/Off switch (Item 12) to the "I"
position (Fig. 10).
6.2 Switching off
Switch the equipment off by turning the On/Off
switch (Item 12) to the "0" position (Fig. 10).
6.3 Spraying
WARNING!
Note the attached leafl et with the safety
instructions.
•
Do not use a very wide jet when spraying
plants or other objects directly.
•
When the release lever on the spray gun
handle is pressed, recoil forces can occur
suddenly, in the worst case scenario causing
the spray tube to point towards the body.
Always keep tight hold of the spray gun
handle.
•
When spraying, you can keep the spray tube
in the holder as shown in Fig. 1 or hold it in
your hands instead.
6.3.1 Switching spraying on/off
•
To spray, press the release lever on the spray
gun handle (Fig. 11).
•
The spray jet will stop when you let go of the
release lever.
•
If the release lever is pressed and then
pushed forward (Fig. 12), this locks the lever.
The equipment continues spraying until
the release lever is pulled back again and
released.
Notes!
1. If the integrated pump contains too little
spray solution or none at all, it will run after
the chemical sprayer is switched on. Press
the release lever on the spray gun handle for
several seconds. The pump will fi ll up and
spray solution will be ejected irregularly. Once
the spray solution is ejected evenly, the pump
will switch off upon releasing the release lever
and will switch on again upon pressing the
lever.
2. If there is too little spray solution in the spray
solution tank, the pump will suck in too little
spray solution (see 1.) and will continue to run
upon releasing the release lever. Top up with
spray solu-tion (see section 5.4).
Anl_GE-WS_18-75_Li_USA_SPK7.indb 13 Anl_GE-WS_18-75_Li_USA_SPK7.indb 13
EN
6.3.2 Adjusting the spray jet
The spray jet can be adjusted on the nozzle from
a single jet to a wide spray (fi ne mist) for larger
areas.
1. Pause the spraying process.
2. Turn the adjustable spray head
counterclockwise to make the jet narrower
until it is a single jet (Fig. 13/Item 1).
3. Turn the adjustable spray head clockwise to
make the jet wider (Fig. 13/Item 1).
6.3.3 Lengthening the spray tube
1. Loosen the locking nut (Fig. 14/Item 3) by
turning it counterclockwise.
2. Pull the telescopic tube outwards to adjust it
to the desired length (Fig. 15).
3. Then turn the locking nut (Fig. 14/Item 3)
clockwise again to tighten.
6.4 Transport
Carry the spray gun by the handle (Fig. 1/Item 11)
or the shoulder strap (Fig. 1/Item 16).
6.5 Charging the Lithium-Ion battery
(not included)
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.6 Battery capacity indicator
(Fig. 6 / item 19)
Press the battery capacity indicator switch (20).
The battery capacity indicator (19) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depth-discharged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.
- 13 -
15.11.2022 12:43:22 15.11.2022 12:43:22