EGO CH2100E Manual De Instrucciones página 5

IMPORTANT SAFETY INSTRUCTIONS
◾
Save these instructions. This manual contains
important safety and operating instructions for EGO
56V Charger CH2100E.
◾
Before using the battery charger, read all instructions
and cautionary markings on the battery charger, the
battery and the product using the battery.
WARNING:
When using electric appliances, basic pre-
cautions should always be followed, including the following.
◾
To reduce the risk of injury, close supervision is
necessary when an appliance is used near children.
◾
Only use attachments recommended or sold by manufacturer.
◾
Do not use outdoors.
◾
For a portable appliance – To reduce the risk of
electrical shock, do not put charger in water or other
liquid. Do not place or store appliance where it can fall
or be pulled into a tub or sink.
CAUTION:
To reduce the risk of injury, charge only
lithium-ion rechargeable batteries. Other types of batter-
ies may burst, causing personal injury or damage.
SPECIFICATIONS
Charger Input 220-240V~ 50Hz 210W
Charger Output
3A 56V
Approximately 40 minutes for
BA1120E battery pack
Approximately 50 minutes for
BA1400/BA1400T battery
pack
Approximately 80 minutes for
BA2240E/BA2240T battery
pack
Approximately 100 minutes
Charging Time
for BA2800/BA2800T battery
pack
Approximately 115 minutes for
BA3360 battery pack
Approximately 145 minutes
for BA4200/BA4200T battery
pack
Approximately 190 minutes for
BA5600T battery pack
Optimum Charging
5°C-40°C
Temperature
Charger Weight 1.2 kg
DESCRIPTION
KNOW YOUR CHARGER (Fig. A)
1. Cooling Air Port
2. Mounting Slot
3. Electrical Contacts
4. LED Indicators
5. Wall Mounting Holes
OPERATION
HOW TO CHARGE THE BATTERY PACK
WARNING:
Do not use the charger outdoors or
expose it to wet or damp conditions. Water entering the
charger will increase the risk of electric shock.
NOTICE: Lithium-Ion battery packs are shipped partially charged.
Before using it the first time, fully charge the battery pack.
1. Connect the charger to the power supply (220-240V~ 50Hz).
2. Align the raised ribs of the battery pack with the
mounting slots in the charger; slide the battery pack
down onto the charger as Fig. B shown.
3. The charger will communicate with the battery pack to
evaluate the condition of the battery pack.
4. When the battery pack is charging, the green LED
on the charger will flash. The power indicator on the
battery pack will flash in sequence: red, orange and
green. (For BA1120E, BA1400, BA2240E,BA2800,
BA3360, BA4200), The last segment of 5-LED indicator
on the battery pack will flash green (For BA1400T,
BA2240T, BA2800T, BA4200T, BA5600T). The fan in
the charger continuously works to cool the battery
pack.
5. When the battery pack is fully charged, the green LED
will stop flashing and will shine green continuously. The
power indicator on the battery pack will go out. Wait until
the cooling fan stops, remove the battery pack from the
charger and disconnect the charger from the power supply.
6. The battery pack will fully charge if left on the charger,
but it will not overcharge. If the battery pack remains on
the charger for one month or more, it will perform self-
maintenance and drop to 30% charge capacity. If this occurs,
reinstall the battery pack on the charger to recharge it fully.
NOTICE:
◾
A significantly reduced run time after fully charging the
battery pack indicates that the batteries are near the
end of their usable life and must be replaced.
◾
The charger may warm during charging. This is part
of the normal operation of the charger. Charge in a
well-ventilated area.
56 VOLT CHARGER — CH2100E
EN
5