Descargar Imprimir esta página

EINHELL TE-MG 300 EQ Manual De Instrucciones Original página 28

Ocultar thumbs Ver también para TE-MG 300 EQ:

Publicidad

Idiomas disponibles

Idiomas disponibles

6. Operation
6.1 Switching on/off
Slide the switch (1) forwards to switch on the
equipment.
6.2 Practical tips
Switch on the equipment.
Work away from the body.
Never move your hands into the direct vicinity
of the work area.
Use only plug-in tools which are in good wor-
king order and undamaged.
Plug-in tools
Sawing: Sawing wood and plastic.
Notes on working practice: When sawing, watch
out for foreign bodies in the workpiece and remo-
ve these if necessary. Plunge cutting is allowed
only in soft materials such as wood or plaster-
board.
Sanding/grinding: Surface sanding/grinding at
edges, in corners or hard-to-reach areas. Depen-
ding on choice of sanding/grinding paper for the
sanding/grinding of wood, paint, lacquer, etc.
Notes on working practice: This equipment off ers
particularly high performance for the sanding/
grinding of hard-to-reach corners and edges. To
sand/grind profi les and channels you can also
work with just the tip or the edge of the sanding/
grinding disk. Various sanding/grinding papers
are available, specially designed for the diff erent
types of material you may be working on and the
amount you wish to remove from the surface.
The amount removed will depend largely on the
choice of sanding/grinding paper and pressure
applied to the sanding/grinding disk.
Scraping: Scraping off old paint or adhesives.
Notes on working practice: Move the plug-in tool
against the area you want to remove. Begin with
a fl at angle of incidence and little pressure. The
surface (e.g. wood, plaster) may be damaged if
too much pressure is used.
6.3 Speed control (Fig. 6)
You can select the speed by turning the speed
controller (4).
Plus direction:
Higher speed
Minus direction:
Lower speed
Anl_SA_TE_MG_300_EQ_Kit_SPK8.indb 28
Anl_SA_TE_MG_300_EQ_Kit_SPK8.indb 28
GB
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
authorized after-sales service or similarly trained
personnel to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician
and/or an authorized service agent.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician or the
authorized service technician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
- 28 -
18.12.2018 09:45:46
18.12.2018 09:45:46

Publicidad

loading