Descargar Imprimir esta página

Publicidad

Enlaces rápidos

448 SWIVEL SHELF
TOOLS REQUIRED:
#2
#2
#2
3
8
5
64
#2
ESTIMATED ASSEMBLY TIME:
30 MIN
CARE AND MAINTENANCE:
Clean with a damp cloth and wipe
parts dry.
WATCH TUTORIALS OF OUR
PRODUCTS BEING INSTALLED
WWW.REV-A-SHELF.COM/VIDEOS
PARTS LIST
No.
Description
A
448 Swivel Frame
B
Side Lock Sub Assembly
C
10-32 X 1/2 Phillips Head Screws
D
10-32 Nylock Nuts
E
Blum Lock Shaft
F
Blum Release Lever
G
M4 X 6 Flat Head Screws
H
Blum Stop Bracket
I
Slide Set Template
* Dependant on unit purchased
D
E
C
H
I
8" SOFT-CLOSE PULLOUT WITH BLUM TANDEM SLIDES WITH BLUMOTION
TOOLS REQUIRED:
3
32
ESTIMATED ASSEMBLY TIME:
30 MIN
CARE AND MAINTENANCE:
Clean with a damp cloth and
wipe parts dry.
Attaching slide to cabinet
PARTS LIST
1) Using the mounting template locations, pre drill 4 holes using a 3/32" drill bit.
- Frame/Slide assembly
2) Remove template and attach the slide assembly to the floor of the cabinet using (4) #8 x ¾" deep thread
- (4) #6 x ½" flat head screw
screws provided.
- (4) #8 x ¾" deep thread pan
head screw
3) With the slides in the fully closed position, place the frame on the slides and push back until you feel the
slides engage the locking devices (you will hear a click sound). Fully cycle the frame a few times.
- Template
- Rub Bushing Kit
Attaching the cabinet door
1) Loosen the (4) lock nuts (3/8" wrench) inside the front wall of the unit. (See Fig 1)
2) Pull the Adjustable Door Mounting Brackets to ensure that you are mounting to the "thick" portion of the
cabinet door. (Front of pull out should line up with front of face frame).
3) Use the (4) #6 x ½" flat head screws provided to attach the door to the pullout unit.
4) If the door needs to be tilted to lay flush against the face frame, loosen the 8mm nuts and turn the "T-Nut"
screws so that it pushes against the metal bracket. Each corner can be adjusted independently. (Note: It is
recommended that door bumpers be used on each corner to ensure quiet operation)
Install rub bushings using enclosed kit and instructions (Note: Chassis may need to be removed for proper installation)
INSTALLATION INSTRUCTIONS: 448 SWIVEL SHELF
Qty.
1
2
2
2
2
2
2 or 4*
2
1
F
Louisville, KY 40299
12400 Earl Jones Way
rev-a-shelf.com
Customer Service: 800-626-1126
Screw and Pilot Hole
Location (4) Places
T-Nut Screw for
Lock Nut
Tilt Adjustment
Fig 1
Fold Template along this edge to fit
cabinet opening.
Front edge of paper
to front of cabinet
(or front of face frame)
T-448SC-1219
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
A
B
G
I-448SW-0822

Publicidad

loading

Resumen de contenidos para Rev-A-Shelf 448

  • Página 1 Install rub bushings using enclosed kit and instructions (Note: Chassis may need to be removed for proper installation) WWW.REV-A-SHELF.COM/VIDEOS Fold Template along this edge to fit cabinet opening. Front edge of paper to front of cabinet (or front of face frame) T-448SC-1219 INSTALLATION INSTRUCTIONS: 448 SWIVEL SHELF I-448SW-0822...
  • Página 2 Using the (7) #6 x 1/2 flat head screws, screw the bracket with the lock lever attached back into the frame. (See Figure 3). Place the lock shaft on the lock trigger as shown (See Figure 4). Lock lever mounting bracket Customer Service: 800-626-1126 | rev-a-shelf.com...
  • Página 3 (4) M4 X 6 flat head screws (See Figure 4). Screw locations Screw locations STEP 4 FIG. 5 Using the (14) #6 x 1/2 flat head screws, screw the brackets with the release levers attached back into the frame. (See Figure 5). INSTALLATION INSTRUCTIONS: 448 SWIVEL SHELF...
  • Página 4 STEP 1 FIG. 1 Using the (2) 10-32 X 1/2 Phillips head screws and (2) 10-32 Nylock nuts, attach the BLUM “stop” to Stop the 448 slide lock sub assembly (See Figure 1). Back View Nylock Nuts STEP 2 1-5/8”...
  • Página 5 12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 INSTRUCCIONES DE INSTALACIÓN / LES INSTRUCTIONS D’INSTALLTION ESTANTE GIRATORIO 448 / 448 TABLETTE PIVOTANTE HERRAMIENTAS REQUERIDAS: OUTILS REQUIS: Lista de partes / Liste des pièces Descripción / Description Qty.
  • Página 6 Support de montage du support de montage avec le levier de verrouillage levier de verrouillage fixé dans le cadre. (voir la figure 3). Placez l’arbre de verrouillage sur la gâchette de verrouillage comme indiqué (voir la figure 4). Customer Service: 800-626-1126 | rev-a-shelf.com...
  • Página 7 À l’aide des (14) vis à tête plate #6 x 1/2, visser le support de montage avec le levier de verrouillage fixé dans le cadre. (voir Illustration 5). INSTRUCCIONES DE INSTALACIÓN: ESTANTE GIRATORIO 448 LES INSTRUCTIONS D’INSTALLTION: 448 TABLETTE PIVOTANTE...
  • Página 8 Detener / Arrêter Con los (2) tornillos de cabeza Phillips 10-32 X 1/2 y (2) tuercas Nylock 10-32, fije el “tope” BLUM al subconjunto de bloqueo deslizante 448 Vista trasera / Vue arrière (consulte la Figura 1). À l’aide des (2) vis cruciformes 10-32 X 1/2 et des (2) écrous Nylock 10-32, fixer la «...