Publicidad
INSTRUCCIONES DE INSTALACIÓN /
ESTANTE GIRATORIO 448 / 448 TABLETTE PIVOTANTE
HERRAMIENTAS REQUERIDAS:
OUTILS REQUIS:
#2
#2
#2
3
8
5
64
#2
TIEMPO ESTIMADO DE ENSAMBLADO:
DUREE ESTIMÉE DE L'ASSEMBLAGE:
30 MIN
CUIDADO Y MANTENIMIENTO:
ENTRETIEN ET MAINTENANCE:
Limpie con un paño húmedo y
seque las partes.
Nettoyez avec un linge humide et
essuyez les piéces pour les secher
complétement.
VER VIDEOS DE
INSTALACIONES DE PRODUCTOS
REGARDER DES VIDÉOS
D'INSTALLATIONS DE PRODUITS
WWW.REV-A-SHELF.COM/VIDEOS
Lista de partes / Liste des pièces
No.
Descripción / Description
Bastidor giratorio 448 / 448 cadre pivotant
A
Subconjunto de bloqueo lateral
B
Sous-assemblage de verrouillage latéral
Tornillos de cabeza Phillips de 10-32 X 1/2
C
Vis cruciformes 10-32 x 1/2
Tuercas Nylock de 10-32 / Écrous Nylock 10-32
D
Eje de bloqueo Blum / Axe de verrouillage Blum
E
Palanca de liberación Blum / Levier de déverrouillage Blum
F
G
M4 X 6 Flat Head Screws
H
Blum Stop Bracket
I
Slide Set Template
* Dependant on unit purchased
D
E
C
H
I
8" SOFT-CLOSE PULLOUT WITH BLUM TANDEM SLIDES WITH BLUMOTION
TOOLS REQUIRED:
3
32
ESTIMATED ASSEMBLY TIME:
30 MIN
CARE AND MAINTENANCE:
Clean with a damp cloth and
wipe parts dry.
Attaching slide to cabinet
PARTS LIST
1) Using the mounting template locations, pre drill 4 holes using a 3/32" drill bit.
- Frame/Slide assembly
2) Remove template and attach the slide assembly to the floor of the cabinet using (4) #8 x ¾" deep thread
- (4) #6 x ½" flat head screw
screws provided.
- (4) #8 x ¾" deep thread pan
3) With the slides in the fully closed position, place the frame on the slides and push back until you feel the
head screw
slides engage the locking devices (you will hear a click sound). Fully cycle the frame a few times.
- Template
- Rub Bushing Kit
Attaching the cabinet door
1) Loosen the (4) lock nuts (3/8" wrench) inside the front wall of the unit. (See Fig 1)
2) Pull the Adjustable Door Mounting Brackets to ensure that you are mounting to the "thick" portion of the
cabinet door. (Front of pull out should line up with front of face frame).
3) Use the (4) #6 x ½" flat head screws provided to attach the door to the pullout unit.
4) If the door needs to be tilted to lay flush against the face frame, loosen the 8mm nuts and turn the "T-Nut"
screws so that it pushes against the metal bracket. Each corner can be adjusted independently. (Note: It is
recommended that door bumpers be used on each corner to ensure quiet operation)
Install rub bushings using enclosed kit and instructions (Note: Chassis may need to be removed for proper installation)
INSTRUCCIONES DE INSTALACIÓN: ESTANTE GIRATORIO 448
LES INSTRUCTIONS D'INSTALLTION: 448 TABLETTE PIVOTANTE
LES INSTRUCTIONS D'INSTALLTION
F
12400 Earl Jones Way
rev-a-shelf.com
Louisville, KY 40299
Customer Service: 800-626-1126
Screw and Pilot Hole
Location (4) Places
T-Nut Screw for
Lock Nut
Tilt Adjustment
Fig 1
Fold Template along this edge to fit
cabinet opening.
Front edge of paper
to front of cabinet
(or front of face frame)
T-448SC-1219
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
Qty.
A
1
2
2
2
2
2
B
2 or 4*
2
1
G
I-448SW-0822
Publicidad
