LiftMaster LM60EVFA Instrucciones De Montaje Y Manejo página 4

2 Intended use
This garage door opener has been designed in accordance with the requi-
rements of the EU Machinery Directive 2006/42/EC; GB (UK,NI): Supply of
Machinery (Safety) Regulations 2008 SI 2008 No� 1597� The garage door
opener has an integrated radio receiver� Optional accessories are available
and described, they may have different use. The garage door operator is
intended exclusively for the opening and closing of garage doors (please refer
to section 6 "Door Types")� The device is not meant for commercial use but
solely for the use in private garage doors that are appropriate for a single hou-
sehold. Note the manufacturers specifications regarding the door and operator
combination� The door must meet mechanical requirements according EU:
EN 12064; GB (UK, NI) BS EN12604� Any improper use of the drive could
increase the risk of accidents� The manufacturer assumes no liability for such
usage� Only the original accessories may be connected to the drive� With this
drive, the door must comply with the current and valid international and coun-
try-specific standards, guidelines, and regulations EU: EN 13241/EN 12543,
EN12604; GB (UK, NI): BS EN 13241/BS EN 12453/ BS EN12604�
3 Scope of supply
Please check the supplied parts for completeness before starting the in-
stallation� Note: The numbering only applies to the corresponding section�
Parts overview:
1� Drive head
2� Remote control
3� Rail bracket (rotating)
4� Hardwarebag
5� Wireless Wall Control*
6� Curved door arm 90°**
6a� Photocells-Set**
Hardwarebag:
Truss head screw
14�
6 x 80 mm
15� Lock nut M6
16� Hexagonal head screw
17� Nut M6
18� Bolt
4 Product overview
Parts overview (Rail):
1x 7� Door bracket
2x 8� Header bracket
1x 9� Adapter for gear wheel
1x 10� Curved door arm
1x 11� C-bracket
1x 12� Hanging bracket
1x 13� 2-piece rail
LM80EVFA*, LM100EVFA*, LM130EVFA**
1x 19� Safety cotter pin
1x 20� Screw ST 6 x 50 mm
4x 21� Screw ST 6,3 x 18 mm
4x 22� Plug
1x
a� Header bracket
b� Belt
c� Rail
d� Carriage
e� Connecting piece
f� Rail bracket
g� Hanging bracket
5 Before you begin
IMPORTANT NOTE
If your garage does not have a side entrance, an external emergency
release should be installed� This allows for manual operation of the
garage door from the outside during power failure�
6 Door Types
Mechanical requirements according EU: EN12604 / GB (UK, NI): BS
EN 12604�
A� One-Piece Door with Horizontal Track Only�
B� One-Piece Door with Horizontal and Vertical Track – Special
canopy door arm is required and the Protector System™ required�
See your dealer�
C� Sectional Door with Curved Track�
1x
1x
D� Canopy door – Special canopy door arm and the Protector Sys-
tem™ required� See your dealer�
1x
1x
E� The Canopy Door Arm for use on door types B and D�
2x
F� Side moving sectional door - In the opening direction, the gap
2x
between the main edge in open direction of a side moving sectio-
1x nal door and the opposite edge must be more than 500 mm� See
section F installation drawing�
Preparation
7
First, check whether your door is balanced and in equilibrium� Open your door
about halfway and let it go� The door can now hardly change its position inde-
1x
pendently, but must remain in this position held by the spring force alone�
4x
1� The rail of the garage door MUST be connected securely and firmly to
8x
the supporting wall or ceiling above the garage door�
4x
2� Additional brackets and mounting rails (not included in the supply) might
be required, if the your garage ceiling has a cladding, boards or similar�
3� If your garage does not have a separate side entrance, an external
emergency release (refer to section 34 "Optional Accessories") must be
installed�
h� Power cable
i� Drive head
j� Release
k� Straight door arm
l� Curved door arm
m� Door bracket
en 3