Stadler Form E-008 Manual De Instrucciones página 8

2. Take the Remote Sensor
the packaging. Open the battery compartment (4) on the underside of
the Remote Sensor
batteries into the battery compartment (4), as shown on page 4, and
close the lid again. Now place the Remote Sensor
3. On the one hand, the Remote Sensor
guarantees precise humidification by its external position. On the other
hand, the Remote Sensor
the humidity sensor Remote Sensor
table or a sideboard with an optimal distance from Eva between 3 – 5 m.
The Remote Sensor
the room air can flow past the sensor (5) as freely as possible. If this is
not possible, we recommend positioning the Remote Sensor
minimum distance of 30 cm from the wall and a minimum distance of 2 m
from windows and ventilation openings.
4. Remove the water tank (6) by holding it by the handle and pulling it
up. Screw off the water tank lid (7) and fill the water tank with clean,
cold tap water up to the maximum mark. Make sure that the anticalc
cartridge (8) has been soaked in water for 24 hours prior (see "Before
setup"). Finally, screw the lid (7) back on the water tank (6). Then place
the water tank (6) in the unit. The water tray (9) will now slowly fill from
the water tank. Important: please do not move the appliance when it is
filled with water. The water could run into the electronics.
5. Press the on/off button (10) to switch Eva on. The current relative humid-
ity in % is shown on the display (15). If the water level indicator light (16)
is red, there is too little water in the unit. The humidification output level
is pre-set to level 3 and the desired humidity at 45 %.
6. Activate the Remote Sensor
(11a). The humidity sensor automatically sends information about the
measured relative humidity several times per minute to the unit, which
shows it on the display (15). The measurement can also be activated by
pressing any button on the Remote Sensor
button (10)).
7. The desired humidity can be changed by pressing the "Hygrostat" but-
ton (11) several times (30 – 75 % and continuous operation "CO"). The
symbol on the display (15) blinks during input. After a few seconds with-
out input, the selected value is saved. The symbol changes to the current
measured humidity.
Info: Once the desired air humidity is reached, the appliance stops and
the display blinks. Should the measured current air humidity fall below
the set value, the appliance begins to humidify again.
8. The humidification performance can be changed by pressing the "Out-
put" button (12) several times (levels 1 – 5). The level is indicated on the
display (15) by horizontal bars (e.g. 1 bar = level 1).
9. By pressing the "Warm" button (13), the warm mode, and with it the
water pre-heating, is turned on. Now the LED on the "Warm" button
on the unit is on. The heating plate (17) warms the water before it is
turned to mist by the ultrasonic membrane (19). The warm mode creates
a pleasantly warm mist plus increases the humidification performance.
10. By pressing the "Auto" button (14), the auto mode, and with it the Adap-
tive Humidity
button on the unit is on. In auto mode, the unit adapts the humidification
(2), the stand (3) and the two batteries out of
TM
(2) by turning the lid anticlockwise. Insert the two
TM
(2) also serves as a remote control. Position
TM
should be positioned centrally in the room so that
TM
TM
Technology, is activated. Now the LED on the "Auto"
TM
(2) is a humidity sensor and
TM
(2) in the centre of the room on a
TM
(2) by pressing the "Hygrostat" button
(2) (aside from the on/off
TM
(2) on the stand (3).
TM
with a
TM