Stiga MP1 550 Li D48 Serie Manual De Instrucciones página 119

Lift the rear discharge guard (Fig.13.A) and in-
1.
sert the chute plug (Fig.14.B) in the discharge
opening, keeping it slightly tilted to the right.
Fasten it by inserting the two pins
2.
(Fig.14.C) in the specific holes until the
hook claw engages (Fig.14.D).
Lift the side discharge guard (Fig.14.A).
3.
Insert the side discharge chute (Fig.14.E).
4.
Close the side discharge guard (Fig.14.A) so as
5.
to lock the side discharge chute (Fig.14.E).
To remove the chute plug:
Lift the rear discharge guard (Fig.13.A).
1.
Press on the centre to release the claw (Fig.13.D).
2.
6.1.3 Cutting height adjustment
Adjust the cutting height as indicated in par. 5.6.
6.2 SAFETY CHECKS
Perform the following safety checks and check that the
results correspond to those outlined on the tables.
Always carry out the safety checks before use.
General safety check
6.2.1
Object
Grips
Handle
Cutting means
Rear discharge guard;
grass catcher
Side discharge guard;
side discharge chute
Switch command
Operator presence lever
Drive ON lever
Battery
Screws/nuts on the
machine and on the
cutting means
Cooling air ducts
Machine
Result
Clean, dry.
Fixed firmly to the machine.
Clean, not damaged
or worn.
Good condition. No
damage. Properly installed.
Good condition. No
damage. Properly installed.
The lever must move
freely, it must not need
forcing and should
return automatically
and rapidly back to
the neutral position.
No damage to the casing,
no liquid leakage.
Correctly tightened
(not loose).
Not clogged.
No signs of damage
or wear.
6.2.2 Machine operating test
Action
Start the machine
1.
(par. 6.3).
Enable the cutting
2.
means (par.6.3 ).
Release both op-
3.
erator presence
levers (Fig.20.A).
Start the machine
1.
(par. 6.3).
Operate the drive
2.
lever (para 5.4).
Disengage the
3.
drive lever.
Test driving
If any of the results fail to match the indications
provided in the tables, do not use the machine! Contact
an Authorised Service Centre to have it checked and
repaired if necessary.
START-UP
6.3
NOTE Start up the machine on a flat
surface without obstacles or high grass.
NOTE Check if the battery combination is
correct, following the instructions supplied
in the "Technical data" table.
Open the hatch for accessing the bat-
1.
tery compartment (Fig.15.A).
Insert the batteries correctly in
2.
their housing (par. 7.2.3).
Insert the safety key (Fig.16.B) com-
3.
pletely and turn it to "ON" position.
Press the start button (Fig.17.A) The dis-
4.
play remains switched on for 15 sec.
Engage the cutting means by first pressing the
5.
safety button on the right side (Fig.18.A) and then
pressing the operator presence lever (Fig.18.B).
To engage the traction, press the le-
6.
ver behind the handle (Fig.18.C).
EN - 7
Result
The display turns
1.
off and the machine
is ready for use.
The cutting means
2.
should move.
The levers should
3.
return automatically
and rapidly to the
neutral position, the
motor must switch
off and the cutting
means must stop
within a few seconds.
The display turns
1.
off and the machine
is ready for use.
The wheels should
2.
move the ma-
chine forward.
The wheels should
3.
stop and the machine
stops moving forward.
No abnormal vibrations.
No abnormal sound.