Jennair KSIS730PSS Manual Del Propietário página 19

AquaLift Self-Cleaning Technology
®
AquaLift Self-Cleaning Technology is a first-of-its-kind cleaning
®
solution designed to minimize the time, temperature and odors
that ordinarily come with traditional self-cleaning methods. With
AquaLift Self-Cleaning Technology, an exclusive coating on the
®
interior of the oven is activated with heat and water to release
baked-on soil. To use AquaLift
wipe out loose debris, pour water into the oven bottom and run the
AquaLift Self-Cleaning cycle. When the cycle finishes in under
®
1 hour at a lower temperature than traditional self-cleaning
methods, just wipe out the remaining water and loose debris. See
the "Clean Cycle" section in the Owner's Manual for more detailed
instructions. For additional information, frequently asked
questions and videos on using AquaLift
Technology, visit our website at
http://whirlpoolcorp.com/aqualift.
Surface Temperature
When the range is in use, all range surfaces may become hot,
such as the knobs and oven door.
Storage Drawer
When the oven is in use, the drawer may become hot. Do not
store plastics, cloth, or other items that could melt or burn in the
drawer.
Oven Vent
The oven vent releases hot air and moisture from the oven, and
should not be blocked or covered. Do not set plastics, paper or
other items that could melt or burn near the oven vent.
Electronic Oven Controls
Control Display
The display will flash when powered up or after a power loss.
Press Cancel to clear. When the oven is not in use, the time of day
is displayed. If the range is in Energy Save mode, the display will
be blank when not in use.
Tones
Tones are audible signals, indicating the following:
One Tone
� Valid keypad press.
� Oven is preheated (long tone).
� Function has been entered.
� Reminder, repeating each minute after the end-of-cycle tones.
Three Tones
� Invalid keypad press.
Four Tones
� End of cycle.
Use the Clock/Tools keypad to change the tone settings.
Self-Cleaning Technology, simply
®
Self-Cleaning
®
Energy Save
The Energy Save mode puts the range into sleep mode and
reduces energy consumption.
To Activate the Energy Save Mode:
1. Press Clock/Tools until "ENERGY SAVE" is displayed.
2. The current setting will be displayed.
3. Press the "1" keypad to adjust the setting.
4. Press Cancel to exit and display the time of day.
5. The setting will be activated after 5 minutes.
To Deactivate the Energy Save Mode
1. Press Clock/Tools until "ENERGY SAVE" is displayed.
2. The current setting will be displayed.
3. Press the "1" keypad to adjust the setting.
4. Press Cancel to exit and display the time of day.
5. The clock will reappear in the display and the range can be
operated as usual.
Settings
Many features of the oven control can be adjusted to meet your
personal needs. These changes are made using the Clock/Tools
keypad.
Use the Clock/Tools keypad to scroll through the features that can
be changed. Each press of the Clock/Tools keypad will advance
the display to the next setting. After selecting the feature to be
changed, the control will prompt you for the required input. Then
press Start or Cancel to exit and display the time of day. Details of
all of the feature changes are explained in the following sections.
Press Cancel to exit Settings.
Clock
The Clock can use a 12- or 24-hour cycle.
1. Press Clock/Tools until "CLOCK" is displayed.
2. Use the number keypads to set the time of day.
3. Press Start to change the time.
4. Press "3" for AM or "6" for PM.
Fahrenheit and Celsius
The temperature is preset to Fahrenheit but can be changed to
Celsius.
1. Press Clock/Tools until "TEMP UNIT" is displayed.
2. The current setting will be displayed.
3. Press the "1" keypad to adjust the setting.
4. Press Start or Cancel to exit and display the time of day.
Audible Tones Disable
Turns off all tones, including the end-of-cycle tone and keypress
tones. Reminder tones are still active when all tones are disabled.
1. Press Clock/Tools until "SOUND" is displayed.
2. The current setting will be displayed.
3. Press the "1" keypad to adjust the setting.
4. Press Start or Cancel to exit and display the time of day.
Sound Volume
Sets the volume of the tone to either high or low.
1. Press Clock/Tools until "SOUND VOLUME" is displayed.
2. The current setting will be displayed.
3. Press the "1" keypad to adjust the setting.
4. Press Start or Cancel to exit and display the time of day.
End of Cycle Tone
Activates or turns off the tones that sound at the end of a cycle.
1. Press Clock/Tools until "END TONE" is displayed.
2. The current setting will be displayed.
3. Press the "1" keypad to adjust the setting.
4. Press Start or Cancel to exit and display the time of day.
19