Publicidad
Idiomas disponibles
Idiomas disponibles
Use the following chart as a guide when setting heat levels.
Setting
Recommended Use
9 to Boost
� Bring liquid to a boil.
9
� Start cooking food.
7 to 8
� Quickly brown or sear food.
6 to 7
� Hold a rapid boil.
5 to 6
� Fry poultry or meat.
� Cook soups, sauces, and gravies.
4 to 5
� Maintain a slow boil.
� Stew or steam food.
3 to 5
� Simmer.
1 to 2
� Keep cooked food warm.
� Melt chocolate or butter.
Simmer
� Maintain a slow boil.
Auto Mode
To Use:
To Turn On:
1. Check that a surface cooking area has been selected.
2. Touch Auto to toggle and select between Melt, Simmer, and
Boil functions. "-" next to the selected function will light up.
When melting foods, such as chocolate or butter, the surface
cooking area can be set to the Melt function for minimum
power level. Similarly simmer and boil functions can also be
used as required.
To Turn Off:
Touch the surface cooking area Off keypad.
Boost Mode
For maximum power level operation, all cooktop touch-activated
electronic controls can be set to the Performance Boost function
when bringing liquids to a fast and rapid boil. Select the desired
surface cooking area, and then touch "Boost" on the heat level
slider to immediately reach the highest setting.
NOTE: This mode can be used on one left hand side cooking area
and one right hand side cooking area simultaneously or can be
used on any one cooking area. Cooking area/areas can operate in
this mode maximum for 10 minutes.
Hot Surface Indicator
An "H" will appear in the heat setting display of a surface cooking
area that is too hot to touch, after that surface cooking area is
turned off.
22
Bridge
The Bridge function allows you to use 2 cooking zones as an
extra-large cooking zone. Use the bridge area to create an oblong
heated area to cook with large or oblong cookware.
To Turn On the Bridge:
1. Place large or oblong cookware on the bridge area.
A
2. Touch POWER. The cooktop will turn on.
3. Touch Bridge.
The heat setting levels for the 2 left surface cooking areas will
default to "0" and can be set from a minimum of "1" to a
maximum of "9."
4. Slide a finger on the heat level slider to change the power
level up or down.
The selected heat level will show in the heat level display for
each surface cooking area using the bridge.
To Turn Off the Bridge:
1. Touch Bridge.
The surface cooking areas will resume operation as 2
separate areas.
NOTE: Performance Boost cannot be used on the same elements
in combination with the Bridge function.
Control Lock
Touch and hold the control lock keypad for 3 seconds to lock the
cooktop controls.
Touch and hold the control lock keypad again for 3 seconds to
unlock the cooktop controls.
Ceramic Glass
Clean the cooktop after each use to help avoid scratches, pitting,
abrasions, and to condition the glass surface. Ceramic glass
cooktop cleaner and a cooktop scraper are also recommended for
stubborn soils. Do not use abrasive cleaners, cleaning pads, or
harsh chemicals for cleaning. The Cooktop Care Kit Part Number
31605 contains all of the items needed to clean and condition your
ceramic glass cooktop. Refer to the "Range Maintenance and
Care" section in the Owner's Manual for additional information.
IMPORTANT: To avoid permanent damage to the cooktop surface
and to make soils easier to remove, clean the cooktop after each
use to remove all soils.
� Avoid storing jars or cans above the cooktop. Dropping a
heavy or hard object onto the cooktop could crack the cooktop.
� To avoid damage to the cooktop, do not leave a hot lid on the
cooktop. As the cooktop cools, air can become trapped
between the lid and the cooktop and the ceramic glass could
break when the lid is removed.
A.
Bridge area
Publicidad
