Publicidad
Idiomas disponibles
Idiomas disponibles
OBJ_BUCH-947-007.book Page 17 Friday, July 8, 2016 10:44 AM
Intended Use
The measuring tool is intended for measuring distances,
lengths, heights, clearances, and for the calculation of areas
and volumes. The measuring tool is suitable for measuring in-
doors and outdoors.
Technical Data
Digital Laser Measure
Article number
Optical sight
Measuring range
Measuring accuracy (typical)
Lowest indication unit
Operating temperature
Storage temperature
Relative air humidity, max.
Laser class
Laser type
Laser beam diameter (at 25 °C) approx.
– at 10 m distance
– at 150 m distance
Batteries
Rechargeable batteries
Battery life, approximately
– Individual measurements
– Continuous measurement
Weight according to EPTA-Procedure 01:2014
Dimensions
Degree of protection
A) The working range increases depending on how well the laser light is reflected from the surface of the target (scattered, not reflective) and with in-
creased brightness of the laser point to the ambient light intensity (interior spaces, twilight). In unfavourable conditions (e.g. when measuring out-
doors at intense sunlight), it may be necessary to use the target plate.
B) In unfavourable conditions (e.g. at intense sunlight or an insufficiently reflecting surface), the maximum deviation is ±20 mm per 150 m. In favour-
able conditions, a deviation influence of ±0.05 mm/m must be taken into account.
C) In the continuous measurement function, the maximum operating temperature is +40 °C.
D) The width of the laser line depends on the surface characteristics and on the ambient conditions.
E) Less measurements are possible when using 1.2 V rechargeable batteries than with 1.5 V batteries. The battery life listed refers to measurements
without display illumination and audio signal.
The measuring tool can be clearly identified with the serial number 20 on the type plate.
Product Features
The numbering of the product features shown refers to the il-
lustration of the measuring tool on the graphic page.
1 Latch of the positioning pin
2 Button for continuous laser beam
3 Function-mode button
4 Button for length, area and volume measurement
5 Result button
6 Plus button
7 Button for measuring and continuous measuring
Bosch Power Tools
GLM 150
3 601 K72 000
–
A)
0.05–150 m
B)
±1.0 mm
0.1 mm
C)
–10 °C...+50 °C
–20 °C...+70 °C
90 %
2
635 nm, <1 mW
D)
6 mm
D)
90 mm
4 x 1.5 V LR03 (AAA)
4 x 1.2 V HR03 (AAA)
E)
30000
E)
5 h
0.24 kg
66 x 120 x 37 mm
IP 54 (dust and splash water
IP 54 (dust and splash water
protected)
8 Button for selection of the reference level
9 Display
10 View finder of the optical sight (GLM 250 VF)
11 Display-illumination button
12 Minus button
13 Button for minimum and maximum measurement
14 Spirit level
15 Button for measured-value list
16 On/Off and memory delete button
17 Fixture for carrying strap
English | 17
GLM 250 VF
3 601 K72 100
A)
0,05–250 m
B)
±1.0 mm
0.1 mm
C)
–10 °C...+50 °C
–20 °C...+70 °C
90 %
2
635 nm, <1 mW
D)
6 mm
D)
90 mm
4 x 1.5 V LR03 (AAA)
4 x 1.2 V HR03 (AAA)
E)
30000
E)
5 h
0.24 kg
66 x 120 x 37 mm
protected)
1 609 92A 1YW | (8.7.16)
Publicidad
